25358672891 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Excessive ice formation on cooling coils of the freezer section led me to believe that air must be finding its way into the freezer section, which led me to think that the freezer section was not adequately sealed.
Ordered gasket and gasket arrived within 48 hrs. Put the unit into out-of-commission status. Defrosted cooling coils. Dried the coils thoroughly. Reinstalled cover panel to the coils. Removed existing door gaskets. Installed new (2) gaskets. So far ice buildup to the coils had ceased.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerri from Burnet, TX
- Parts Used:
- 218904404
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
The housing on the filter cup was cracked
I removed the old housing (three screws) , pulled it out about three inches and discounnected the two water lines. Then I put the new one on, attached the two water lines & I had water immediately & ice within a couple of hours.
Really it was a no brainer, but I'm sure I saved at least $50 doing it myself.
Really it was a no brainer, but I'm sure I saved at least $50 doing it myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Azle, TX
- Parts Used:
- 5303918277
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Original Ice Maker quit working.
Loosened the 2 screws a little so that it would slide up and off then unplugged the wire harness.
Installed the new one in reverse order and works like a champ.
Installed the new one in reverse order and works like a champ.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ANGELA from MEBANE, NC
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator Light bulb went out
I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Snellville, GA
- Parts Used:
- 218904404
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Water overflowing from Water filter housing.
Discovered water filter housing broken allowing water to leak out when using water in door function.
Found part number using Part Select diagrams. Ordered part from Part Select,. shipping time about 3 days.
Removed 3 screws houlding from cover over housing assembly. Removed cover, removed old, broken part by pulling water lines from top of unit. Replaced new housing in place, connected above mentioned water lines, replaced cover and holding screws. Tested for leaks. Everything worked great.
Found part number using Part Select diagrams. Ordered part from Part Select,. shipping time about 3 days.
Removed 3 screws houlding from cover over housing assembly. Removed cover, removed old, broken part by pulling water lines from top of unit. Replaced new housing in place, connected above mentioned water lines, replaced cover and holding screws. Tested for leaks. Everything worked great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Tolland, CT
- Parts Used:
- WFCB, 5303289501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower drawer broke from age.
The longest part of replacing the drawer was swapping all the veggies out of the old one. No tools,slid the glass drawer front from the old one and slid it into the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas J from Dawsonville, GA
- Parts Used:
- 5303917954, 218169802
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
freezer cold other side for milk warm
the heater defroster was bad. tested and no continuity brake in eliment.just doing a visual might have detected it but it`s hidden behind the coils.....all is working now
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Chugiak, AK
- Parts Used:
- WFCB, 5303289320, 215744100, 215314301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Lower Hinge wearing into door bottom
Ordered parts, and replaced them. Living in Alaska it made the shipping take a little longer but they arrived and now the top hinge dosen't pop out, door shuts nicley and we were able to turn the temp. control down which in the long run will save electricity.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Scranton, KS
- Parts Used:
- 5303917954
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Coils freezing up and refrigerator would get warm
Wasn't sure if it was the derost timer or the heating element. Since the timer was much cheaper, I bought it and crossed my fingers.
My story is like the others. Unplug the refrigerator, snip the old wires, strip back the wire insulation, use the supplied connectors to attach the new defrost timer to the existing wiring.
Success! My coils no longer freeze up.
Only difficulty is I am a large guy, and fitting my upper body into the freezer was challenging.
My story is like the others. Unplug the refrigerator, snip the old wires, strip back the wire insulation, use the supplied connectors to attach the new defrost timer to the existing wiring.
Success! My coils no longer freeze up.
Only difficulty is I am a large guy, and fitting my upper body into the freezer was challenging.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregg from Mohnton, PA
- Parts Used:
- 5303917954
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Freezer frosted up
Removed old thermostat and replaced. really easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michele from Smithfield, UT
- Parts Used:
- 5303918277
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
I replaced the icemaker
I removed the two screws and unplugged it. I then attached the pigtail to the appliance, then to the fridge. I had to push the excess wire harness into the hole in the back. It took a few minutes to move the rest of the harness out of the way by curving it upward and securing it with a nylon tie.I ordered the ice maker from Part Select on Sunday night and it arrived at 8:32 Tuesday morning, THANK YOU! I ordered very simple weed cutter parts from Sears a week ago and they haven't even shipped yet!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from Lithonia, GA
- Parts Used:
- 5303917954
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Freezer was getting a build up of frost on the condenser and wasn't cooling.
First I remove the back panel which had 4 screws. Then I removed the ice maker. The icemaker is held in place by the 2 screws that requires backing the screws out just a litter, than lift up and remove the electrical connector. Used a volt ohm meter to check the resisitant in the heater element and the defrost timing switch. Both tested good and that left only the thermostat. Removed and replaced the thermastat swich. I cut the ends of the old switch and crimp the ends of wire with the crimps that came with the swict i purchased from parts select. My refrigerator is working properly and making ice like normal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Else from Plant City, FL
- Parts Used:
- 5303917954, 215846602
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
coils freezing refrigerator not cooling
The defrost timer is located under the freezer side behind the lower plastic cover. Very simple, just 2 screws and a plug, and your done.
The thermostat requires removing the lower drawers in the freezer and unscrew the back side of the rails and let them hang over to get access to the lower cover on the back of the freezer. Once the panel is off you will be able to see the thermostat. From there you just remove the thermostat from the clip, cut the 2 wires, splice in the new thermostat and re install using the new clip and your done!!
This was my first time and it was really simple. I had a local repair shop quote me $375.00 . I did it myself for under 50.00 shipped to my door..
The thermostat requires removing the lower drawers in the freezer and unscrew the back side of the rails and let them hang over to get access to the lower cover on the back of the freezer. Once the panel is off you will be able to see the thermostat. From there you just remove the thermostat from the clip, cut the 2 wires, splice in the new thermostat and re install using the new clip and your done!!
This was my first time and it was really simple. I had a local repair shop quote me $375.00 . I did it myself for under 50.00 shipped to my door..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Woodstock, IL
- Parts Used:
- 5303918277
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker stopped working (Very oxidized residue)
I removed the old ice maker and unplugged the cable. Screwed in the new one with a 1/4 nut driver at the 2 mounting screws, plugged cable in. Checked ice maker with a small level before final. All Ok and after night I had Ice and it has been working great since.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from PHOENIX, AZ
- Parts Used:
- 241798231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Replace ice maker which was splashing water
Turn off ice maker
Slide wire harness shield off connector
Disconnected harness
Loosened 2 wall screws
Remove old ice maker
Installed new one reversing process
Slide wire harness shield off connector
Disconnected harness
Loosened 2 wall screws
Remove old ice maker
Installed new one reversing process
Was this instruction helpful to you?
Thank you for voting!