25331610102 Kenmore Refrigerator - Instructions

Simply replaced the defrost timer located inside the frig just behind the temp dial. Very easy job. Removed the 3 screws holding the temp sw and light assembly. Removed the defrost timer w/ 2 screws and put i all back together. 15 mins at most. Suggest you watch the install video for pointers.

per the video..easy installation....unfortunately the temperature did not improve. We still have a refrigerator temp in the upper freezer.....and a "cooler" in the refrigerator section

After some troubleshooting to ensure the thermostat and heating element were working, determined that the defrost timer was the problem. With the defective part, I was able to manually advance the timer to activate the defrost cycle, but it wouldn't do so on its own. Unplugged the refrigerator from the wall. Timer is located in the refrigerator compartment at the very top. The compartment houses the cooling thermostat, the light bulb and the defrost timer. Using 1/4" nut driver, remove 4 screws holding compartment cover to top of fridge. Lower a bit to access electrical wiring. Wiring harness can be unplugged to work on the timer away from the fridge which makes it a bit easier. Timer is mounted with 2 phillips head screws. Remove screws and unplug timer from wiring. Install new timer, plug in wiring, secure with the phillips head screws and remount entire compartment.

followed the video very esay

Removed the lower trim panel from front of fridg. and loosened two screws enough to turn it about 1/4 inch so the screw heads were in the larger holes. Pulled it out disconnected the wire connector and transfered the heat shield and screws to the new clock, connected the wire connector and aligned the screws. tightened them and job done. Has worked like new sense. Thanks Roger

unplug fridge,Then take rack out n remove the 2 screws on the icemaker set aside,then remove 2 screws on the back panel, cut wires n splice in new part! put back the same.

Removed the timer, installed the new one. Great service from part select

Exactly as the video showed, except I had to take the evap coil cover off and use a hair dryer to thaw it out. It was still frosting up too much, so I ordered the thermostat as well. Both were really easy, once i saw the location of the defrost timer and the thermostat. Thanks for the great site, prices that put the big store to shame, and the good video too!

Refrigerator and freezer was not cooling sufficiently due to an inoperative evaporator cooling fan. Replacing the mini evaporator fan was extremely easy. Here are the steps needed to replace the fan. Step 1: Unplug refrigerator/freezer main power cord from the electric wall outlet. Step 2: Remove the food rack from the freezer compartment. Step 3: Using a 1/4" nut driver, remove the (2) 1/4" screws that hold the freezer vent panel/temperature control in place. Step 4: After removing the screws, disconnect the motor's wire harness connector which is located on the top left corner behind the freezer's vent panel/temperature control. Step 5: Pull away the entire vent panel/temperature control panel and lay it flat on a table. Step 6: Remove the vent cover from the main panel by holding the left side and the right side of the vent cover and squeeze both ends at the same time. Step 7: With the motor now being visible pull the motor's fan blade straight off. Step 8: Using the 1/4" nut driver, remove the (2) screws that hold the motor bracket to the rear of the main panel. Step 9: Using the 1/4" nut driver remove the (2) screws that hold the motor to the bracket and the (1) ground wire screw. Step 10: Install new motor back onto the bracket with the original (2) screws and the (1) ground wire screw onto the same locations.Step 11: Re install the (2) screws that mount the fan bracket to the back of the main vent panel.Step 12: Push the motor's original fan blade back on the shaft until it's fully seated. Step 12: Snap back in place the small vent panel back onto the main panel. Step 13: Push in place until you hear a click, the motor's wiring harness connector back onto the top left corner of the freezer's main power wire harness connector. Step 13: Push the main vent panel until it's in place and then reinstall with the original (2) 1/4" screws. Step 14: Reinstall the freezer's food rack back in place. Step 15: Plug in the main power cord into the wall outlet. Get ready to enjoy ice cold drinking water and a super cold freezer. Pete,your weekend mechanic

Instructions from partselect were very clear and probable cause made it easy to narrow things down. I have the manual for the refrigerator that shows the location of the defrost timer. Very surprised that it turned out to be a cheap and easy fix.

Checked defrost timer. It was a shocker: it was completely burnt out. Replaced it with the new part very easily. I thought now it would defrost properly but unfortunately the thermostat also was shot. I had ordered it along with the timer just in case. It was not expensive at all and I saved time but having it with me when I replaced the timer. NOW ALL IS WELL AND REFRIGERATOR SECTION COLLING PROPERLY. THANKS TO VIDEO AND PARTSELECT.

1 went with maj 69% said defrost timer. NO. 2 went with second choice run cap NO. 3 went with my thought, ( PTC Starter ) why not, most exp part. Fixed the problem.

Defros timer was easy I finished it in about 15 minuts but the defrost themostat was hard.I had ploblems with the wire conectors and the tape I had to use Twist-on wire connectors.I hope I will not have problems later.So far 1 week later it is working.I can't belive $50 saves me $600.Thanks to Part Select for the video and how fast they shipping my parts in less than 2 days.

The website said 60% of people with same refrigerator problem solved the problem with a new fan kit. I received the fan kit within 3 days of ordering. Was shipped from Fresno, CA to Long Beach, WA. The fan kit was to be installed behind rear panel in the freezer compartment. When I removed the old fan motor, I noticed the shaft turned harder than the new fan motor, suggesting a problem with the old fan motor. I plugged in the obvious fan motor power bundle with no problem. The instructions and diagram with the kit nearly steered me wrong. Instructions, diagram and splices with the kit instructed to cut the "extra" wire bundle and splice "similar" wires (should have said same color wires). Luckily, I ignored those instructions when I remembered the U-Tube video depicted the extra wire bundle was to be inserted into a factory penetration in the back panel, facing the freezer compartment. This power bundle is for adding an ice maker, which my refrigerator did not have. When reassembled and the refrigerator restarted, I could immediately feel forced air in the refrig, where there was no flow before fixing. I observed that all the refrig and freezer dials do is act like a valve to increase or decrease air flow to the compartments. The dials have no mechanical or electrical connections, just designed to divert air flow from across the cold 'evaporator' fins. I recommend other consumers to remember carefully what they see in the video and watch again if stumped during the job. The video was better than the instructions which may have been written in China or India. I am happy. Repair was a lot cheaper than a new refrigerator and I would not have bought another Frigidaire. Thanks to this website. r. andersen

The instructions given to me by part Select were very good.I replaced the Timer- checked the heater with oham meter it was good- checked the door weather striping it was good and replaced the thermostat with new .So at this point I may need to call a professional unless some one has another solution.