3639550950 Kenmore Refrigerator - Instructions

1. pry off small square plastic cap on top and bottom of old handle with thin blade tip of paring knife. Careful not to damage small tabs on the backside corners. 2.Pry off long trim insert above the handle with the paring knife and loosen bottom most screw revealed. 3. unscrewed 2 screws revealed by step 1, one on upper handle end and one on the lower. 4. pull upper cap end from the door and lift the handle upward and away from the door. 5. slide the new handle and door end into the lower trim piece. 6. fasten all 3 screws. 7.snap in upper trim strip and square plastic caps back in place.

Removed control panel by inserting small screwdriver in the 3 holes underneath to loosen. Remove 4 screws holding circuit board . Unplugged 3 connectors. Removing circuit board gave access to flapper. Removed flapper by unclipping. Installed new flapper and reversed disassembly procedure. This was 2nd time in 2 years I had to replace this part.

I followed the video instructions (very helpful) and used others comments for removing the control panel. For the latter I used a small allen wrench to carefully wedge the bottom two indents (look from below panel edge) slightly up and forward to release the panel. Next, after removing the four screws, the assembly (housing shield) removed fairly easily. I then had full access to the flapper and removed this carefully with the pliers so as not to damage the piece it was attached to (Dispenser Door Recess Crank?). The rubber outer flange on the otherwise plastic flapper was very irregular for approx. 1/4 of the circumference and thus did not seal. So far it's been one week and no more frost build up or frozen water dispenser line.

Took the paper clip, pressed in through the holes on the bottom of the ice dispenser panel. Removed the four screws. Loosened the panel and removed the wires. replaced the flapper door. Then reversed the process. Your video was VERY helpful except for the paper clip. Had to get that off another web site.

Followed video. Changing flap was not difficult but did not fix the problem.

Really easy- turned off ice maker, powered down appliance briefly. Removed ice maker by removing 3 screws with 1/4 nut driver. Unplugged ice maker from power supply. Removed and replaced solenoid arm assembly. Reversed steps and whammy - ice cubes dropped.

Snapped off the plastic plate covering the dispenser. Removed the four screws holding the mechanism in place. Remove the electrical connections. Pull the mechanism out and up carefully pulling the dispenser pad out with all the mechanism in place. Look at the mechanism before removing any parts to get a mental image so that reassembly will be easy. Remove any electrical switch or circuit boards and remove old parts before submerging the mechanism in hot soapy water for clean-up. The Clean-up will take longer than the disassemble and reassembling. After completion the dispenser works as it should.

I followed the video instructions to the letter and it was very easy and a total success. I believe I would have had problems but for thr video demonstration which was very clear and straight forward in a simple manner. Thanks for the prompt delivery of the part and the help installing it.

Your Video really made it easy, showing the actual replacment of the part. However I did have one problem, which was I could not unplug the panel just by pulling on the plugs. A locking catch is on each plug so I just moved the panel out of the way.

Watched the video from your site and followed instructions, extremely easy after that.

I followed the repair video Partselect provided online. It the repair easy and fast. Great video!!!!

Removed ice select control unite from freezer by removing 3 nut screws holding unite in place. Disconnect 2 electrial plug ins.Remove unite from freezer and place on table for easy work space. Remove 4 nut screws holding Solenoid & Arm. Replace with new Solenoid & Arm. Reinstall back in freezer and now we have cube ice again.

I followed the video instructions. They were clear and consise. I removed the trim ring and controls. Them removed the housing and flapper. I did notice a small burr in the plastic chute and foam insulation. I trimmed this off with a utility in hopes this burr caused the flapper to warp. This is the 2nd time the flapper has been replaced in 1.5 yrs. The repair was really easy thanks to the video.

Watched à video provided at your website. Removed te cover then removed 4 screws holding the control panel' snapped out the old flap and inserted the new one.

My husband made the replaced the flapper while watching the video provided in your email, it was easy. Thank you.