25360899401 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ben from FRANKLIN, TN
- Parts Used:
- 240524102
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Noisy condenser fan
Remove lower cardboard refrigerator panel. Carefully pull existing cracked fan blade off of the motor shaft and replace with new fan blade. Reinstall cardboard panel.
Was this instruction helpful to you?
Thank you for voting!
refer door hinges were lost during the move in to our first home.
The center door hinge was still attached to the refridgerator so I only had to install the bottom and top hinges. I also moved the door handles to the other side so the doors open the "right" way. The hinges were just 2 bolts and 3 screws. Now, just if the repair man from our home warrentee company would show up to fix the refridgerator. It's blowing hot air!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DANIEL from CAPE CORAL, FL
- Parts Used:
- 5303918202, 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
FREEZER COMPARTMENT NOT COLD ENOUGH (20 DEGREES)
REPLACED TIMER-DEFROST 215846602..REPLACED THERMOSTAT-DEFROST KIT 5303918202..REPLACED CONTROL, TEMPERATURE 5304421256..RECHARGED SYSTEM WITH 134A...ALL FANS WORKING...COMPRESSOR RUNS.. FREEZER STILL NOT GETTING COLD ENOUGH...HOLDING AT 20 DEGREES...ANY SUGGESTIONS..THANKS..DAN
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karla from UNION, MO
- Parts Used:
- 241554901
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Socket set
Refrigerator light stopped working
The bulb wasn't the issue so I was hopeful the switch was. utube helped me some, but figuring my model was different than any on utube. Got the switch in and plugged it back in. Moment of truth. Didn't light. Ugggh! Out $50 for switch plus $20 for nut driver set.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from PHILADELPHIA, PA
- Parts Used:
- 5303918202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Evaporator was freezing up and was running non stop
I tested the components in the refrigerator defrost function. I used digital multimeter and checked for continuity. Defrost thermostat must 32 degrees or lower.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sadrudin from SAN DIEGO, CA
- Parts Used:
- 218396700
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
The hole on the handle mounting block was too low
I had to loosen the screw holding the mounting block and increase the hole size to fit the screw on refrigerator
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Newton, KS
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Refer iced up and would not keep the bottom cool. It was 70 Farenheit inside.
I simply removed 4 screws holding the casing and then 2 more holding the timer. It was very easy. I then replaced the timer by unplugging and plugged the new one in. I replaced all the screws and the job was done. Less than 30 minutes. I was very impressed with the shipping time. When I ordered the part, I had it the next day.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from VENICE, FL
- Parts Used:
- 5303918202
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Refrigerator evaporator coil was icing up
The evaporator coil is behind the freezer. Remove the rack that makes the shelf and remove two 1/4” hex head screws I the back of the freezer to access the coil.
I used a hair dryer to melt the ice off the coil.
The thermostat clips on the refrigeration pipe to the coil. Remove the old thermostat and cut the wires at least a few inches from the thermostat. Clip the new thermostat on the pipe and strip about a 1/4” of the wire ends. The electrical connectors (provided with the new part) must be crimped to connect the wires.
I used a hair dryer to melt the ice off the coil.
The thermostat clips on the refrigeration pipe to the coil. Remove the old thermostat and cut the wires at least a few inches from the thermostat. Clip the new thermostat on the pipe and strip about a 1/4” of the wire ends. The electrical connectors (provided with the new part) must be crimped to connect the wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gene from pensacola, FL
- Parts Used:
- 240530811
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken meat drawer
new drawer was received within 2 days and was extremely simple to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from PERRIS, CA
- Parts Used:
- 5303918549
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers
Fridge and freezer both freezing at bottom and warm at top.
Unplugged fridge. Removed freezer shelves and unscrewed and removed plastic shelf brackets. Removed the lower rear panel. Removed the bin for ice. Removed the 2 exposed upper rear panel screws. At this point I was able to flex the panel quite enough to access the fan motor. Carefully plugged the fridge back in and turned it on long enough to verify the existing evap. fan motor was not running. Powered off and unplugged again. Removed the fan and it's support assembly, and replaced with new. Had to cut the wires and splice and crimp with the provided wire nuts since the plugs in this model were different. Powered on fridge to check fan function. Reassemble and go home looking' like a hero! Saved my BFF a couple hundred bucks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Eatonville, WA
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Defroster didn't work
Ordered a new defroster timer and replace old one. It works just fine. A $35 repair vs a $500 new appliance.
Cool.
GWE
Cool.
GWE
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Sunnyvale, CA
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
No freezing or cold in either freezer or refridgerator - compressor did not run.
Traced issue to defrost timer ( burned compressor & element contacts). This unit is mounted next to the temperature adjustment control in the refridgerator area - right in front. Removal of plastic cover provided easy access to the timer. Unit unscrews from the mounting then unplugs. Installation is reverse of removal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nickalas A from CUYAHOGA FLS, OH
- Parts Used:
- 240530811
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
our meat drawer handle was broken
I just put the new one in with no problem
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Landover, MD
- Parts Used:
- 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bilb went out
replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lorraine from Arlington, VA
- Parts Used:
- 242161202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
very Simple!
Insert the bottom part of the trim first, then pull up to snap on the top. PartSelect.com is a fantastic website!!
Was this instruction helpful to you?
Thank you for voting!