25379802981 Kenmore Refrigerator - Instructions

Took old defrost pan off, put new one on. Had to bend new defrost pan a little for it to fit..

Occasionally, we'd get one batch of ice cubes and a frozen lake of water in the bottom of the ice tray.

The installation was easy and I won't bother duplicating the comments of others who have installed this part.

One word of caution: The ice maker contains a heating element on the bottom. That element is apparently live even when the ice bar is in the upper (off) position. When I unscrewed the old ice maker and went to lift it off the bolts, I severely burned my finger on the bottom of the old ice maker because apparently I started the repair in the middle of the heating cycle.

I highly recommend that you unplug the ice maker entirely before doing the replacement and gingerly ensure that the unit isn't hot before touching it. You'll save yourself a nasty burn.

watched the video (VERY helpful) and then removed the old icemaker and replaced it with the new one. Difficult only because of the small working space in the side by side freezer plus you can't see what you're doing when you tighten the screws. Working like a charm now.

From most posts I've read, the defrost timer was the culprit so I blindly ordered one. Easy install but did not fix the problem so I broke out the ohm meter. The only other 2 items it could be all tested good with my meter so I bypassed the defrost thermostat (per forum help...actually quite easy)and it defrosted fine, which told me I needed a new defrost thermostat. Installed fairly easy and problem gone.

Having tried PartSelect.com before, I was very comfortable with the process. Input my symptoms and the feed back I received was that one of the 2 things (Defrost Timer or Defrost Thermostat)might need replacement. Since the cost was not much and over night shipping would cost more than the product, I decided to order both the parts. Changing parts was a breeze. The instructions posted by others on your web site were very easy to follow. You guys save me a bundle every time I have any thing going worng with any of my appliances.

Loosen two screws, unplug power, lift it off, put new one on and make sure water chute is correct place, tighten screws!

I unsnapped the old clips from the bar, installed one end cap to freezer door, clipped other end cap to bar, slid bar into end cap installed in door then snapped other end cap into place. Repeated for second shelf bar as those end caps were broken as well. No tools were needed.

It was very simple, used a nut driver to loosen the attachment nuts that held the ice maker in place. Disconnected the wiring harness. Removed the leveling tab from old ice maker and attached it to the new one. Then reassembled in the reverse order. As they say it was no brainer! The best part of the repair, was hearing the ice dump.

This refrigerator is less than 2 years old. I have had to replace the ice maker 2 times now. Cheap ass parts! Only one ice maker you can order so just be prepared to replace it yearly!

A little research told me the hum plus no cooling was either the compressor or the relay. I ordered the new relay and put it in but it didn't fix the problem. I ended up having to buy a new fridge, but it was worth the $30 gamble to see if I could fix it on the cheap and it saved me the money a service call would've cost. Pretty easy installation, just in a tight space on my model.

Dear Part-select,
I had a fridge that was not working food was melting in the freezer, Beer was warm. You get the picture anyway using your site I found the parts needed to to fix the issue in fact I ordered two parts one fixed the issue 50% and the other like 30% of the time! both parts with overnight shipping were cheaper than 1 part if purchased at our local appliance part outlet:) not to mention the cost of a repair person. Thanks again! . Keep up the good work


Tom Houck
Spokane, WA
Houck Photo
509-723-3418
tomhouck1@comcast.net

I found that the fill solenoid for the ice maker was down to a drip when energized. I ordered from this site and replaced. now plenty of water, but the ice maker would just stall and jump teeth. The heater which heats the ice up to free it from the mold was defective. Ordered from this site, and now working great.this sitet has good pricing, and the help illustration is great, and explains the sequence of events. This made it easy to troubleshoot. This refrigerator has not give a problem in over 11 years. The problem is "the ice maker". I have replaced it 6 times.

removed ice maker storage holder and then remove two philip screws and unplugged four pin connector. removed ice maker and installed new one . very easy to do

Problems. Two screws holding temperature control module to the plastic case did not fit the holes in temperature controler were too big. So I used gorilla glue to help secure but it was still loose a little bit with all the connections made i turned it on but it did not work

They were the wrong parts. I read a question another person asked and it advised to order these parts. Didn't want to waste my time anymore and threw them away.