Models > 363WR30X0316 > Instructions

363WR30X0316 Kenmore Refrigerator - Instructions

Jump to:

All Instructions for the 363WR30X0316
61 - 75 of 202
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
WALTER from SPRING HILL, FL
Parts Used:
WR17X2770, WR17X2769
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
original parts broken (poor design)
Unscrewed four screws, two on each part, and replaced broken parts, reinserting screws. This is a no-brainer repair.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Craig from Bothell, WA
Parts Used:
WR17X2770, WR17X2769
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
broken slide rails
Basically I removed 4 screws holding the rails together, did a little cleaning of the existing parts that I would re-use and screwed the 4 screws back in and put it back into the fridge. Piece of cake. If I hadn't cleaned up the old parts it would have taken me 5 minutes.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
janette from huntingtown, MD
Parts Used:
WR17X2769
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
needed to replace broken drawer slide rail,
removed produce drawers, removed center piece front cover, removed glass shelf, removed broken drawer slide rail - unscrewing where attached in the rear of the refrigerator. Also removed screw from centerpiece where broken drawer slide rail was attached. reassembled all very quickly....saved myself having to buy another refrigerator by doing this simple repair.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mark from Keyport, NJ
Parts Used:
WR17X2769
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
My wife forced the fruit drawer in and snapped the slide rail.
I pulled out the shelf and removed the 2 screws holding the broken side rail to the shelf frame. I then screwed the new rail in and set the shelf back in.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Omri and Diklah from Brooklyn, NY
Parts Used:
WR2X8700
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
plastic bracket that holds the shelf to the door was broken.
Simply remove the shelf, remove broken bracket easily, wash the parts, attach the new bracket and place the shelf back in place. No tools.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Richard from Zephyrhills, FL
Parts Used:
WR30X10093
Difficulty Level:
Easy
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Screw drivers
Leaking And Making Stalactites
Had to defrost the freezer to melt off all the ice before servicing. Once that was done the icemaker replacement only took about 15-30 minutes to complete. The new icemaker came with many accessories and adaptors that were not needed and the instructions were based on replacing an older model and not really clear for my model. They mentioned not being able to use the new stripper but it was exactly the same as the old one so I left the new one in place. All in all it was easy and did the job.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dan from HIGHLAND, MD
Parts Used:
WR29X5171
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
On/off switch stuck in the off position
Removed icemaker from freezer,
Removed 3 screws from cover plate, and removed screw securing main gear, removed gear.
Pulled back cover plate to expose switches and mechanism.
Removed screw holding switch to remove switch, and installed new switch.
I should have taken a pic of the cover plate, the interior mechanism and the wiring as I went along. It would have saved me 45 minutes in reassembly. Also, as luck would have it, I reversed the wiring on the switch. So off was on, and I had to remove it, switch wires and re-install.
But it works!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Phyllis C. from Northwood, NH
Parts Used:
WR17X2769
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Slide rail broken at forward mount
Took out shelf & brackets. Removed plastic shelf. Unscrewed broken bracket & screwed in new bracket.
Put back in & replaced the shelf.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Daniel from Chesapeake, VA
Parts Used:
WR17X2770, WR17X2769
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Left drawer slide broken replaced both right and left
Removed drawers and glass shelf. Removed screws that hold old slide rails in place. Installed new rails and re-installed cover for vents. Placed assembly back in and installed drawers.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Regina from Taylorsville, KY
Parts Used:
WR30X10093
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
icemaker quit working when we moved
My husband took out the old icemaker in about 5 minutes. The new icemaker was a perfect fit even though the refrigerator was >10yrs old. The only difficult part was the plug extension that was needed so that it would fit into an older appliance. The part was included, it just made the cord about 3 inches longer than it needed to. After working with it for about 20 minutes we were able to fit it on the back side of the icemaker. Now it works great!!
4 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Anna from Weatherly, PA
Parts Used:
WR17X2769
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
I found a broken slide rail after replacing a center slide rail.
I followed the directions on the site for the center slide replacement. I had actually called a local store and had him order the first part. It took several days and then I started searching online and found this site.Then I ordered the second part on line and to my surprise it arrived the next day. I was fortunate enough to have lived only about 70 miles from the distributer.Following the directions I found here is how I attempted the initial repair. With the vegetable bins out fo the bottom, I removed the plate covering the front frame by gently prying it off. Then I removed the two screws to losen the bar and lifted out the glass shelf. I didn't have much difficulty removing the frame since the front piece support for the slide rail that fit into the frame was already broken. I also had to loosen the screws on the back rail. I removed the entire frame and then replaced the side rail reinserting it into the end caps. I replaced the back screws and then the front ones .I replaced the glass shelf and then the cover cap for the shelf.
The only problem I encountered was that I couldn't seem to get the back screws really tight and I don't know why.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from Wingate, NC
Parts Used:
WR17X2770
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Drawer Slide Rails broken
The bottom shelf of my Mom's fridge broke. I found the part I needed and went to repair it. Realized both sides were broken. Ordered other side as well. Two screws in front, two screws in back. Front side had a metal strip covering screws. Had to pull that off to get to screws. Snapped back on after repair.
Mother was very pleased.
Told her to be careful. Those little pieces of plastic can be expensive.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Nikki from Raleigh, NC
Parts Used:
WR17X2770
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
I broke the left side slide rail while trying to clean out refridgerator
I had one of my guy friends do it for me. It took him less than 10 minutes, and probably would have been quicker if he had a better screw driver. Mine is a cheap girly one that he could not get a good grip on.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Barry from Athens, GA
Parts Used:
WR2X8700, WR2X8699
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
End cap hanger-insert broken
Replace end cap to bottom shelf and then to door.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Keith from East Windsor, NJ
Parts Used:
WR2X8700, WR17X2769
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Two shelf bracket had cracked and needed replacement
After removing the food items, I removed the shelves and separated the existing broken brackets from the still good parts. I then screwed together the old working parts and the new replacement parts, all within about 10 minutes. I then placed the shelves back in the fridge and restored the food. The most time was taken picking from the food because I was hungry, but the repair itself was simple.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 363WR30X0316
61 - 75 of 202