79572063111 Kenmore Refrigerator - Instructions

1. Unplug the refrigerator (to avoid shock) 2. With one screwdriver pry open the switch on the side facing the door to a gap of about 1/8 inch 3. Insert a second screwdriver into the gap to press the plastic tab back slightly and this should release the part. 4. pull the part out and unplug it, you may have to pry back some small tabs on the sides, 5. Plug in the new switch 6. plug in the refrigerator the light should come on, if not tighten the connection 7. Insert new switch back into its slot, it should snap in place. Done!

Slid the replacement shelves into place.

Phillips head screw driver required.

Door stopper attaches to door and front side of refrigerator. Located at the underside of the door at the front of the hinge.

Remove screw, keep screw for installation of new stopper. Remove damaged stopper, install new stopper using the original screw.

Used a small screw driver inserted into the front of the switch (facing the front) and pried until the switch was coming out. When out, I removed the connect harness and replace the switch with a new one.

I ordered the needed parts, the correct ones I thought, but when they arrived, I realized they were the wrong parts shipped to me. The reason the wrong parts were shipped to me was because PartsSelect failed to advise me there were none of the parts I needed available so they shipped the left hand basket assembly, door, versus the desired right hand basket assembly, door. I then had to return the wrong parts shipped to me, at my cost of ~$25, and await a refund for the wrong parts originally shipped to me. That's how I did the repair.

Replace with new switch. this is the third switch i have replaced in 10 years. the only part, besides a light bulb, that has gone bad. obviously this is a problem with this model for Kenmore, or just poor switch design.

Simply removed old gasket. Started in a corner with installing the new gasket. It went in easily and quickly.

Read previous tips
Taped off area around switch to protect surface
Used putty knife to extract switch
Used screwdriver to separate connector from switch
Plugged in connector
Pushed switch assembly into opening
Removed tape

The repair was an easy replacement. The problem was the LG part was no longer available from LG or any of the other places I tried. The PartSelect customer service representative was a true professional and did an outstanding job of helping find the correct part (LG's diagram was unreadable) and cross-referenced it to find the the part that PartSelect actually had in stock. I had the part in four day. The best customer service I have had in years. I lost his name but the order was 13449146. He deserves a raise!

Easy install, small screwdriver under back of old switch push out and pull out with small pliers. unsnap the old plug and install new. YOUR DONE

Six screws to remove the old one (I looked up the process on Youtube) and six screws had it back in tip top shape.
Three wire connections, two were plug in and one was a ground wire.
BTW: It was a 3 wire, not a 6 wire. I had ordered that by mistake and PartSelect made the return and replacement very easy.

Covered the sidewall with tape to protect. Pried the switch out with knife blade and removed electric plug with needle nose pliers. placed plug in new switch and pushed switch into the hole in the side wall. Took about five minutes.

Remove two screws on top of the fridge; removed old switch and inserted new switch. Worked like a charm. Replace casing and screws.

I disconnected the refrigerator power, removed the 2 screws holding the mullion door on the left side of the refrigerator French-door (it’s the flap that allows the door to close). Removed the broken spring and installed the replacement spring in its place. Reinstalled the mullion door by putting it in place and installing the previously removed screws.

Reviewed instructions on YouTube. Removed storage box.Removed Philips head screw on either side of track. Lifted door and placed it on table. Using a flat blade screwdriver removed old gasket (it did not looked damaged). Pressed new gasket into groove in door. Replaced door onto track and replaced screws. Replaced storage box. No more ice buildup.