25361792305 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Janette St from KALISPELL, MT
- Parts Used:
- 240534701
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Had a broken part in the door that holds condiments in
Removed broken part and then snapped in new part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from MONTGOMERY, IL
- Parts Used:
- 5303918202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Coils frozen over. Refrigerator not cooling
I cut wires from bad thermostat and removed it . Stripped wires and crimped connectors on new thermostat and wires from old thermostat. Used heat gun to seal sleeves over connectors. Very helpful video from this site Thanks, you will be my go to parts supplier from now on!!!!!!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brad from STOCKTON, CA
- Parts Used:
- 5303918549
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Refrigerator wasn't getting cold
removed the back panel of the freezer and unplugged the connector for the Motor. Removed the air diffuser, then removed the fan blade. Removed the 2 screws holding the motor to the bracket. Disconnected the old wire harness and installed the new one. Put the fan blade onto the new motor and installed the motor onto the bracket. Put the air diffuser back on, plugged the motor back in and fastened the back panel. Plugged the refrigerator into the outlet and tested, OK!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cristina from MARLBOROUGH, MA
- Parts Used:
- 242193213
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Old gasket was torn and falling out
I removed the old gasket and cleaned the area. Then I started at the bottom and pressed the new gasket into the door. You must use firm pressure and go all around. It does get tricky hear the end as it seems like there is excess, but it will fit. Just keep using firm pressure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Okeechobee, FL
- Parts Used:
- 5303918549
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Intermittent loud noise coming from fan motor located in freezer compartment
Ordered a new evaporator fan motor and watched the repair video supplied by part select on their web site.It was spot on step by step instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aaron from ODESSA, TX
- Parts Used:
- 5303918549, 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Fridge was't cool
I just followed the instructions on the videos.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from NEWHALL, CA
- Parts Used:
- 5303918549
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Evap fan motor comes on and off will not stay running
pulled back panel to get at evap fan motor cut wires to remove reinstalled hooked up wires
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Reginald from WEST PALM BCH, FL
- Parts Used:
- 5303918549
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Noise from fan
I watch the video on your site and this make iit very easy to do. That repair that tooks me 40 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from FREDONIA, KY
- Parts Used:
- 242193213
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
My gasket was worn out and torn.
The repair was much more simple to install than I would have imagined. I watched the video provided on your website. What a simple solution to a nagging problem. My fridge looks great again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JACOB from YOUNGSTOWN, OH
- Parts Used:
- 241537103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Refrigerator did not cycle
Installation was fairly straight forward. The major complaint is that the problem returned 2 weeks later. I don’t know if I care to re-invest in another switch.
Now what?
Now what?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from TUCSON, AZ
- Parts Used:
- 240505801
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light not turning on when door opened
Used a flat head screwdriver to pop out the old switch, removed the contacts and placed on the new switch, popped the switch back in. Done in about 2 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from EDMONDS, WA
- Parts Used:
- 240534701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replace broken shelf protector
simply put the protector shelf bar on shelf !! easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ricky from BUENA PARK, CA
- Parts Used:
- 242193213
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
GASKET OLD LEEKING OUT COLD AIR FROM FRIDGE FOOD WARM
SO SIMPLE I JUST FOLLOWED THE VIDEO THE PARTS SELECT PROVIDED ON THERE WEB SITE AND WALA DONE IN 5minutes Wow THAT EAZY NO TOOLS NESSECCARY JUST A SCREWDRIVER
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from PERRIS, CA
- Parts Used:
- 5303918549
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers
Fridge and freezer both freezing at bottom and warm at top.
Unplugged fridge. Removed freezer shelves and unscrewed and removed plastic shelf brackets. Removed the lower rear panel. Removed the bin for ice. Removed the 2 exposed upper rear panel screws. At this point I was able to flex the panel quite enough to access the fan motor. Carefully plugged the fridge back in and turned it on long enough to verify the existing evap. fan motor was not running. Powered off and unplugged again. Removed the fan and it's support assembly, and replaced with new. Had to cut the wires and splice and crimp with the provided wire nuts since the plugs in this model were different. Powered on fridge to check fan function. Reassemble and go home looking' like a hero! Saved my BFF a couple hundred bucks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gene from pensacola, FL
- Parts Used:
- 240530811
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken meat drawer
new drawer was received within 2 days and was extremely simple to install.
Was this instruction helpful to you?
Thank you for voting!