2538387792 Kenmore Refrigerator - Instructions

I followed the video that came with my email receipt but i had to use the extra electrical adapter, there is no where to put the extra wiring so it is hanging next to the wall. I was glad I didn't have to unplug the fridge. just kept the wire up so no water would come out. It took several hours to start working and it doesn't make as much ice as the old one, but at least it works. It was a very informative video. Thanks

moved freezer items to right of icemaker,loosen two nuts lifted icemaker over nuts,squeezed and pulled cable out turned over marked L bracket screw with marker for location plugged cable in tighten screws,made ice in 2 1/2 hours john

Unplug refrigerator power cord. Remove ice cube bin. Place wire signal arm in down (off) position. Ice Maker is held in place by two (slotted/hex headed) screws through keyhole slots over the top of Ice maker along the left side of freezer. Use mirror to locate screws then carefully loosen (do not remove) screws with a nut driver or screw driver. Lift Ice maker up and right until it releases from the screw heads. Unplug electrical connection. A flat screw driver may be required to loosen connector. Connect new unit electrical and Install new unit over screw heads and tighten screws. Replace Ice Bin and place wire signal arm in the up (on) position. Reconnect refrigerator power cord. After freezer cools down sufficiently it will start making ice.

first replaced dual solenoid, then ice maker. still not working. going to chase electrical next

the first thing was just trying to find parts for a very old product. i searched around till i somehow came across the part select website. and, eureka they had the gaskets ! then, i had a need for door shelf caps. and again, there they were on the exploded schematic ! with the purchase of these plus parts for the door, washers and center and lower hinge pins, i was able to renew our refrig and save a lot of money. removing both doors was very easy and all was done with a minimal amount of manual labor. now the doors are tight and closely evenly.

Followed the video instructions posted below the product. Its a tight area to work in but it can be done. It did not immediately start making ice. I waited and waited.... 3 hrs 4 hrs still not filling up or making ice. Finally I decided to pour some water in the tray and see if it would freeze ice and dump it. It did and immediately started to fill up on its own after that! Its been working perfectly ever since! So dont be alarmed if yours doesnt work immediately and try pouring some water in it if yours doesnt being working within several hrs. I am happy I was able to do this myself and save repair man costs. Its just not work the cost they charge for older appliances.

Unplugged refrigerator. Removed control knob and cover. Unwired control and removed same. Removed plastic tube from old capillary tube and placed on new unit. Installed and wired in new unit, making sure new unit was in the "off" position. Plugged in refrigerator, turned control knob to the first numerical setting, and was rewarded with the startup of the refrigerator compressor. Voila!

The two screws that held the ice maker in place could not be seen do to there location. I could only get one hand inside do to space restriction.So I placed a mirror inside so I could see the screw heads and from point it was very easy to see and line up the nut driver on the screw heads. I then lifted it up and unplugged the wiring and installed the new ice maker. Works like a charm. Paul

Went well overall. I really thought that you guys taking the time to create a very helpful video was awesome. Thanks for doing that! The only difficulty I had was that my old ice maker had the connection toward the front, while the new one was in the back. So I had to use the adapter and had so much extra wiring to bundle, and tie wrap, with little place to go with it that I got frustrated. Wish I just had the correct replacement wire to begin with. Nonetheless, we are stocked with a full bin of ice after about 3-4 days.

loosened two 1/4 in. screws removed ice maker unplugged harness. Plugged back in slid the replacement ice maker over the two screws secured. Done

It was fairly easy to replace the thermostat. Unplug the refrigerator first. Then remove the refrigertor light bulb and 3 screws on the plastic cover that houses the thermostat and defrost timer. Unplug the thermostat from the wiring on the refrigerator and remove the plastic housing holding the thermostat. Remove two screws holding the thermostat and replace with the new one. Put everything back together in reverse order. Unfortunately, this did not corrrect my problem. The refrigerator is well over 30 years old and I had narrowed down the problem to the thermostat because the old one was hard to turn to adjust. About 10 years ago, I replaced the defrost heater in the rear of the freezer compartment for the same problem, and didn't think that would be the problem this time. Well, as it turned out, I checked the resistance on the defrost heater and it was was bad again. I replaced the heater this week I got from PartSelect, and the refrigerator cycles fine now. Replacing the heater is a little more work that changing the thermostat. You have to remove the freezer compartment fan, fan vent, and back inside wall of the freezer section to expose the coils and the heater element. You just need a socket screw driver. Then you have to reach inside and unplug each end of the heater to check it with your ohm meter. A bad element will show up as an open circuit. Then to replace it, you have to maneuver it around to get if away from the coils and remove a couple of clips. Anyone with some common sense can do it, but it can be a bit challenging.

Replaced ice maker - easy to replace but it did not fix the problem.

I watched the video and it seemed pretty easy. I ordered the new ice maker. It arrived in 5 days and I chanted it in less the 30 minutes. A little tricky seeing where you have to loosen the screws but not hard. and in 2 hours I had ice again.

ice maker= replaced overload,microswitch and solenoid water valves.refrigerator=replaced the thermostat.Great price on parts,very fast delivery and parts were a perfect fit.You made the job very easy. John

Called a repair man. He said it was a a sensor type valve at the bottom back of fridge and he would have to order. He never called us, so we went to website and ordered it. Replaced it. It WAS obviously burned out/dicolored. Bracket had to be redone, as it wasn't standard. Didn't work. Ordered new icemaker. Worked like a charm. Video for installing icemaker very helpful. He called a couple weeks later and we already had it fixed.