2539308160 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kenneth from Cypress, CA
- Parts Used:
- 3206319
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice Maker Not Working
Tested for power and found the thermal cut-off bad. Installed new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Annie from West Plam Beach, FL
- Parts Used:
- 5303281398
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Glass Shelf
1) Remove glass from shipping Container. 2) Using fingers, place glass ever so gingerly in the shelf tray. 3) Pour a glass of wine to celebrate.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Albuquerque, NM
- Parts Used:
- 5303281398
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
No problems at all.
Very EASY!! just unpack, wash, and place into slots above crisper doors. A child could do this.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from sicklerville, NJ
- Parts Used:
- 5303918277
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
ice in tray would not release
moved freezer items to right of icemaker,loosen two nuts lifted icemaker over nuts,squeezed and pulled cable out turned over marked L bracket screw with marker for location plugged cable in tighten screws,made ice in 2 1/2 hours john
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russell from Detroit Lakes, MN
- Parts Used:
- 5303918277
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver
The ice maker failed for the second time.
This is the 2nd ice maker replace in the past 20 months. This installation was easier following the experience of the first replacement. The instructions are well written. The pictures or illustrations are difficult. The most challenging part of the installation is routing and fastening the wire harness. The illustration was not helpful. Overall, this is a repair most DIYers should be able to accomplish.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Loxahatchee, FL
- Parts Used:
- 5304456667
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
ice maker not working and refrigerator too cold
ice maker= replaced overload,microswitch and solenoid water valves.refrigerator=replaced the thermostat.Great price on parts,very fast delivery and parts were a perfect fit.You made the job very easy. John
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Sheridan, AR
- Parts Used:
- 5303918277
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
icemaker not working
first replaced dual solenoid, then ice maker. still not working. going to chase electrical next
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Black Hawk, SD
- Parts Used:
- 5303918277
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
water running over ice machine and into kitchen
Called a repair man. He said it was a a sensor type valve at the bottom back of fridge and he would have to order. He never called us, so we went to website and ordered it. Replaced it. It WAS obviously burned out/dicolored. Bracket had to be redone, as it wasn't standard. Didn't work. Ordered new icemaker. Worked like a charm. Video for installing icemaker very helpful. He called a couple weeks later and we already had it fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Louisville, KY
- Parts Used:
- 5303918277
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Ice maker would not make ice or fill up
Followed the video instructions posted below the product. Its a tight area to work in but it can be done. It did not immediately start making ice. I waited and waited.... 3 hrs 4 hrs still not filling up or making ice. Finally I decided to pour some water in the tray and see if it would freeze ice and dump it. It did and immediately started to fill up on its own after that! Its been working perfectly ever since! So dont be alarmed if yours doesnt work immediately and try pouring some water in it if yours doesnt being working within several hrs. I am happy I was able to do this myself and save repair man costs. Its just not work the cost they charge for older appliances.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Wapella, IL
- Parts Used:
- 5303207345
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set, Wrench set
door gasket was broken , sweating and dripping water on the floor
I took the freezer door off took center hinge out , took frig door off , unscrewed inside panel took off old gasket , put the new one on , put inside panel back on , (be sure the flange on the gasket stay's in the groove when you screw it back together) replace doors and anything else that needs replaced ! check the seal !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clemente from El Paso, TX
- Parts Used:
- 5303207345
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
On the left top of the door there an opening. I figure if I replace the gasket it would fix the problem. Well it did not.
The repair to the door ok. But the door is still not level.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Ft. Myers Beach, FL
- Parts Used:
- 5304469396
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
arm wouldn't go all the way down and dump ice
Took front off and found the broken spring, got new one and replaced, now works great. Make sure to unplug as the water can come on and flood the freezer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from SHERMANS DALE, PA
- Parts Used:
- 5303918277
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Stopped making ice.
I watched the video and it seemed pretty easy. I ordered the new ice maker. It arrived in 5 days and I chanted it in less the 30 minutes. A little tricky seeing where you have to loosen the screws but not hard. and in 2 hours I had ice again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from New Berlin, WI
- Parts Used:
- 5303918277
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Ice Maker replacement
Went well overall. I really thought that you guys taking the time to create a very helpful video was awesome. Thanks for doing that! The only difficulty I had was that my old ice maker had the connection toward the front, while the new one was in the back. So I had to use the adapter and had so much extra wiring to bundle, and tie wrap, with little place to go with it that I got frustrated. Wish I just had the correct replacement wire to begin with. Nonetheless, we are stocked with a full bin of ice after about 3-4 days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Akron, OH
- Parts Used:
- 241798231
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Ice maker quit working.
The two screws that held the ice maker in place could not be seen do to there location. I could only get one hand inside do to space restriction.So I placed a mirror inside so I could see the screw heads and from point it was very easy to see and line up the nut driver on the screw heads. I then lifted it up and unplugged the wiring and installed the new ice maker. Works like a charm. Paul
Was this instruction helpful to you?
Thank you for voting!