25379132990 Kenmore Refrigerator - Instructions

From most posts I've read, the defrost timer was the culprit so I blindly ordered one. Easy install but did not fix the problem so I broke out the ohm meter. The only other 2 items it could be all tested good with my meter so I bypassed the defrost thermostat (per forum help...actually quite easy)and it defrosted fine, which told me I needed a new defrost thermostat. Installed fairly easy and problem gone.

watched the video (VERY helpful) and then removed the old icemaker and replaced it with the new one. Difficult only because of the small working space in the side by side freezer plus you can't see what you're doing when you tighten the screws. Working like a charm now.

My brother completed the repair by replacing rack on door and also brackets. The support rack had to be cut to size and then put on overall no too bad.

Occasionally, we'd get one batch of ice cubes and a frozen lake of water in the bottom of the ice tray.

The installation was easy and I won't bother duplicating the comments of others who have installed this part.

One word of caution: The ice maker contains a heating element on the bottom. That element is apparently live even when the ice bar is in the upper (off) position. When I unscrewed the old ice maker and went to lift it off the bolts, I severely burned my finger on the bottom of the old ice maker because apparently I started the repair in the middle of the heating cycle.

I highly recommend that you unplug the ice maker entirely before doing the replacement and gingerly ensure that the unit isn't hot before touching it. You'll save yourself a nasty burn.

Having tried PartSelect.com before, I was very comfortable with the process. Input my symptoms and the feed back I received was that one of the 2 things (Defrost Timer or Defrost Thermostat)might need replacement. Since the cost was not much and over night shipping would cost more than the product, I decided to order both the parts. Changing parts was a breeze. The instructions posted by others on your web site were very easy to follow. You guys save me a bundle every time I have any thing going worng with any of my appliances.

Loosen two screws, unplug power, lift it off, put new one on and make sure water chute is correct place, tighten screws!

After determining the ice maker was getting water but not harvesting the ice, I ordered a replacement Ice Maker. Installation was easy. One electrical connection and two screws. Following the video to make sure I did not miss any steps I had ice in just a few hours. Just in time for a July heat wave!

Unplug refrigerator , loosing two screws. Lift ice maker up to remove from position. Disconnect electrical connection. Reverse procedure to install new ice maker.

Removed 2 screws that hold ice maker in place. Unplugged and took out of freezer. Used the screws I took out to put new ice maker in. Plugged in the power and in 2 days I had a full ice bin and haven't had any worries since. Should have replaced the broken one along time ago but thought that the process was harder than this. Very easy and suggest this to anyone having ice maker issues. Less than $100 and never have to buy ice for the house again.

This refrigerator is less than 2 years old. I have had to replace the ice maker 2 times now. Cheap ass parts! Only one ice maker you can order so just be prepared to replace it yearly!

A little research told me the hum plus no cooling was either the compressor or the relay. I ordered the new relay and put it in but it didn't fix the problem. I ended up having to buy a new fridge, but it was worth the $30 gamble to see if I could fix it on the cheap and it saved me the money a service call would've cost. Pretty easy installation, just in a tight space on my model.

Dear Part-select,
I had a fridge that was not working food was melting in the freezer, Beer was warm. You get the picture anyway using your site I found the parts needed to to fix the issue in fact I ordered two parts one fixed the issue 50% and the other like 30% of the time! both parts with overnight shipping were cheaper than 1 part if purchased at our local appliance part outlet:) not to mention the cost of a repair person. Thanks again! . Keep up the good work


Tom Houck
Spokane, WA
Houck Photo
509-723-3418
tomhouck1@comcast.net

The instructions that came with the replacement icemaker were very complete, in particular concerning the small levelling bracket on the bottom of the icemaker, because the old bracket needed to be removed from the old icemaker and transferred to the new one. This part of the installation might not have been obvious, so I was glad to see it clearly outlined in the instructions. The old icemaker was removed by loosening two nuts and detaching the electrical connector, and the new one was installed in its place. Fairly simple, the whole job took about 45 minutes because I work slowly and carefully. A more confident person could probably have the new one installed in 15 minutes. Only drawback: about three to four weeks after installing the new icemaker it has begun making a loud clicking noise on occasions. It is a repetitive (5 second interval) clicking, and only happens for about a minute every few hours and then stops. I am concerned that it might be gears prematurely wearing out and slipping. I guess I'll know in a few weeks if this one stops making ice.********************************************* Update: after about 9 months the new icemaker quit working and will need to be replaced. I removed the front cover from the icemaker and could clearly see that the teeth of one of the plastic gears were worn out and no longer meshing with the opposite gear. The drive gear was just spinning in place and making no contact with the larger gear.

Moved the old gasket aside to gain access to retaining screws in top freezer door. The new seal in the container we received was twisted, so laid it flat and used a hair dryer (as you advised) to regain the proper shape. Did everything possible, to align the gasket. Opened the freezer door to remove the retaining screws, began to reinstall the new gasket. The top came down both sides well. Attempted to install screws across the bottom, the gasket was so twisted would not conform back into the retaining frame on the bottom of the door. Therefore, it fits poorly. No proper seal. Sincerely, Jesse & Mary(also, the bottom of the freezer door plastic form was very brittle, broke where the screws fit....so we had to make a piece formed like a strip to re-enforce the areas that 'cracked' off so as the screws could align the bottom areas.

Followed on line video. Also water supply tube on fridge was full of ice. You can pull it out and run hot water on it to clear.