10654902300 Kenmore Refrigerator - Instructions

ordered the part, pulled out the icemaker unit, removed the module, put the new module in, reinstalled the ice maker unit and let it run.

Followed on line video

I followed the instructions that was on your site and it was very easy to follow.

Very easy to order from parts select. Took seconds to replace.

I removed two small bolts that secure the flapper that keeps ice from falling out when you open the door, one bolt that holds a cosmetic cover for the wires and slid the icemanker forward. The only difficult part was removing the plug since it was high up, the wires were stiff and there's a release to push that locks the two plugs together. Once it was removed all was installed in the opposire order.
The part I ordered had a slightly taller channel where the water refills so I had to trim it to allow the new icemaker to slide in without bending the fill nozzle. Other than that it was pretty easy.

Long shaft from motor to dispenser was stripped. I removed 2 screws from the shaft holder in door, lifted old shaft out, put new shaft in and replaced the 2 screws. Took 2 mins! Works great!

This one is not rocket science, however, it does take some careful "fudging" to accomplish without additional disassembly. The Ice Guide is held in place by three tabs. The tricky part is "tilting" the center tab into it's hole/slot on the ice dispenser lever (center hole), then tilting it up to snap into place.... there is a very tight tolerance here, with the opening of the ice/water dispensing unit. Be sure to "lock out" the ice maker/water dispenser, in order to be able to use the light. Once snapped in place, all is well.

Removed Ice container; Removed two screws from housing around shaft; Pulled old shaft from freezer door; inserted new shaft in freezer door; replaced housing around shaft; replaced and tightened two screws securing housing; returned ice container. Tested by activating ice dispenser. It worked like new.

directions very well written, easy to follow, no problems

Removed ice maker from fridge. Removed motor assembly (3) screws on cover, and (2) screws inside. Removed mold (3 screws on bottom) and replaced everything in reverse order. Note: Turned ice maker off for several days while waiting for parts. The water line on this particular model will freeze inside the freezer if ice isn't made for several hours/days. You will have to defrost to begin making ice again.

Unplug power to refridg/freezer. Removed the screw in rt. rear bottom of ice maker to remove. After removing slightly, unplug pigtail. Remove ice maker completely. Remove large square cover from left side to expose motor. Remove screws to remove motor. Replce with new. Replace ice maker to freezer, plug pigtail back in, put screw back in rt rear bottom, plug refridg/freezer back into power source. Ice was making in about 2 1/2 hours.

With instructions from PartSelect.com this was an easy fix. I tested the motor's electric as suggested and was satisfied that the Motor Module (WPL W10190935) would correct the problem. UNPLUG THE REFRIGERATOR! I popped the outside plastic cover off to expose the unit. (1) remove the wire unit that runs the length of the cube maker (2) remove the 3 screws that secure the motor unit and carefully remove it (3) carefully line up the new unit, slide in place and replace the 3 screws (4) install the wire that was removed in step(1). Connect electric to the refrigerator and wait about 2 hours for your first ice cubes. PartSelect.com is the ONLY supplier that you will ever need! Great instructions and trouble shooting suggestions. Shipping is incredibly fasssst! Customer contact is awesome. Don't hesitate to buy from them! Saved me about $200.! Good luck....Tom in SC

First I had to figure out how to get the old unit out so I could work on it. The three screws that others wrote about were the ones that hold the motor in place. There are 3 screws holding the ice maker in the frame, along with one screw covering the electrical connection. The electrical connection was difficult to unplug because the locking tab was on the back side of the connection and with no room to work in the freezer it didn't become apparent until several frustrating minutes went by. There were no instructions provided, the picture on the ordering page showed the complete ice maker, and for $80 you get a printed circuit board with a small round item which must be the motor/timer control. The two plastic parts for moving the ice from the ice maker were included but not replaced because I didn't notice them until I had finished replacing the ice maker back in the freezer and wasn't going to start over again.
Once installed, there wasn't any noise, even of water flowing like the old one, could not tell if the unit was working or not. In the morning there was new ice in the bin indicating the repair had been successful. This is like anything else, if you have done it before it is a 5 minuter job but when you have to look at it and try to figure it out it takes a bit longer. All in all, it was simple enough, I was expecting a complete ice maker unit like was in the picture when ordered but only the motor module was actually needed.
We have another refrigerator/freezer that has an icemaker that is over 20 years old and has never been repaired, it is a Sears model though, probably made by Whirlpool or someone else.

I purchased the part and put it in,

To replace the light bulb, I removed the screw and the cover, unscrewed the old bulb, replaced with the new bulb and replaced the cover, securing it with the small screw. It worked appropriately with normal use for a few days and then I noticed the light was not coming on when I opened the door.

I removed the cover and pulled out the bulb to find that the filaments inside are dangling and burned through. I need them replaced, please.