25378822013 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard Allen from PHOENIX, AZ
- Parts Used:
- 241798231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Replacing Icemaker
Pull refrigerator from wall and disconnect the water line and unplug the power.
On top of the icemaker, two machine screws hold the icemaker to the side of the refrigerator. You will have to feel around to find the machine screws, but once you do, it is simple to slip the appropriate size socket over the hex heads. I found it helpful to have an extension on the socket wrench. Disconnect the power cable inside the refrigerator (there are little pressure clips on the side that help release the cable) and move it out of the way for the time-being.
Back out both machine screws several turns, but do not remove them completely. The icemaker slips over the screws, so leaving them in the side of the refrigerator makes that process a lot easier. Hand tighten the machine screws once you have positioned the new icemaker in place. One thing to be sure and do is make sure the water line hose coming out of the back of the refrigerator inside is on top of the icemaker. It fits into a slot in the top of the icemaker - failing to do this will result in water pouring into the freezer compartment, not into the icemaker..
Reconnect the power cable to the new icemaker and tuck it up behind the icemaker assembly. Tighten the machine screws completely, but do not over-tighten.
Reconnect the water line on the back of the refrigerator at the wall, and plug in the refrigerator. You should hear the unit fill immediately.
In about an hour you should have ice filling the bin. Enjoy!
On top of the icemaker, two machine screws hold the icemaker to the side of the refrigerator. You will have to feel around to find the machine screws, but once you do, it is simple to slip the appropriate size socket over the hex heads. I found it helpful to have an extension on the socket wrench. Disconnect the power cable inside the refrigerator (there are little pressure clips on the side that help release the cable) and move it out of the way for the time-being.
Back out both machine screws several turns, but do not remove them completely. The icemaker slips over the screws, so leaving them in the side of the refrigerator makes that process a lot easier. Hand tighten the machine screws once you have positioned the new icemaker in place. One thing to be sure and do is make sure the water line hose coming out of the back of the refrigerator inside is on top of the icemaker. It fits into a slot in the top of the icemaker - failing to do this will result in water pouring into the freezer compartment, not into the icemaker..
Reconnect the power cable to the new icemaker and tuck it up behind the icemaker assembly. Tighten the machine screws completely, but do not over-tighten.
Reconnect the water line on the back of the refrigerator at the wall, and plug in the refrigerator. You should hear the unit fill immediately.
In about an hour you should have ice filling the bin. Enjoy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from SOUTH LYON, MI
- Parts Used:
- 241798231
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker failed
Watched YouTube video. Very easy. Used my cell phone camera in ‘selfie’ mode propped up in the upper right hand corner of freezer to see the 2 hidden screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Las Vegas, NV
- Parts Used:
- 242252603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker stopped working
Took off old part and installed new part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from SAVANNAH, GA
- Parts Used:
- 241537103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Not running
After waiting over 2wks for my part to arrive, I purchased the part locally and made the repair the same day as I am still waiting for the part to arrive from you guys. Your customer service really needs improving. I paid for 2 day shipping, what a joke. I will be returning the part as soon as I receive it thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Torrance, CA
- Parts Used:
- 240358008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rust on freezer shelf
Perfect fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from FORT WAYNE, IN
- Parts Used:
- 242193206
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door Gasket was torn. The frig door not sealing properly
I peeled off the torn door gasket. Then installed new door gasket pushing and pinching it into place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- timothy from georgetown, TN
- Parts Used:
- 242252603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Water Valve was leaking water and not making ice
I unplugged the fridge and unscrewed the back cover,unscrewwd the two screws holding the water valve in place and the water line to the ice maker and the electrical connection and install the new water valve,then buttoned everything back up and plugged the fridge back in and it is working great,making ice as normal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from PHOENIX, AZ
- Parts Used:
- 241798231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Replace ice maker which was splashing water
Turn off ice maker
Slide wire harness shield off connector
Disconnected harness
Loosened 2 wall screws
Remove old ice maker
Installed new one reversing process
Slide wire harness shield off connector
Disconnected harness
Loosened 2 wall screws
Remove old ice maker
Installed new one reversing process
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Juanita from ORANGEBURG, SC
- Parts Used:
- 5304511738
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
both bulbs blown out
unplug refrigerator and insert the bulb in refrigerator first and then insert the second bulb in freezer side. After which, plug the refrigerator back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glen from HENDERSONVLLE, NC
- Parts Used:
- 242077705, 5308000010
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
EVAPORATOR FAN MOTOR & BLADE
The service manual diagram shows the 149 complete fan shroud in a vertical (upright) position. Misleading! Of course.
The actual mounting of the lay in fan shroud fully assembled is in the horizontal position laying in a tray area just above the evaporator coil cage assembly. The entire shroud assembly can be installed incorrectly by the diagram and will still fit. BUT... no cold air will flow or be forced into the ice maker vent nor the refrigerator vent. I found this out the hard way by trial & error.
If the drawing had shown it in the horizontal position for both removal and reinstallation... it would have saved a lot of time and headaches. Also, the diagram does not show the (2) plastic angle supports on the shroud, another scratch your head event. Parts included on drawing... 149, 5, 8, 9, 13, 14 on CTFFHS2611PF4 diagram page of service manual.
ALSO, the (4) lower cabinet plate screws have to be removed, and the first left hand screw counting up to allow the next upper panel to swing out enough to lay the shroud in correctly (horizontal) on top of the evaporator coil cage. BOTTOM LINE... THE AIR FLOW HAS TO BE UP IN ORDER TO WORK PROPERLY.
The actual mounting of the lay in fan shroud fully assembled is in the horizontal position laying in a tray area just above the evaporator coil cage assembly. The entire shroud assembly can be installed incorrectly by the diagram and will still fit. BUT... no cold air will flow or be forced into the ice maker vent nor the refrigerator vent. I found this out the hard way by trial & error.
If the drawing had shown it in the horizontal position for both removal and reinstallation... it would have saved a lot of time and headaches. Also, the diagram does not show the (2) plastic angle supports on the shroud, another scratch your head event. Parts included on drawing... 149, 5, 8, 9, 13, 14 on CTFFHS2611PF4 diagram page of service manual.
ALSO, the (4) lower cabinet plate screws have to be removed, and the first left hand screw counting up to allow the next upper panel to swing out enough to lay the shroud in correctly (horizontal) on top of the evaporator coil cage. BOTTOM LINE... THE AIR FLOW HAS TO BE UP IN ORDER TO WORK PROPERLY.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from CAMAS, WA
- Parts Used:
- 5304511738
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
The replacement substitute stipulated and shipped to us was not compatible with this appliance.
After receipt of the incompatible LED bulb, customer service gave us the phone # of Frigidaire and they helped us to get the correct LED for this appliance. We returned the incorrect bulb to parts Select and are now waiting for a credit to our account at this point. It’s been a long process but our Frigidaire at least is now lighted.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennifer from BUFFALO, NY
- Parts Used:
- 242252603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Icemaker stopped making ice and i knew it wasnt the mechanism since I could hear that working when I unplugged and plugged the unit back on.
I found a couple of videos online of a similar product fix to get a lay of the land. When I got the part, I unplugged the unit and turned off the water. It was easy to take off the back panel and remove the old water intake valve to swap it out for the new one. Once I attached everything again I could see that the valve was taking up water but it didnt seem to be going all the way to the icemaker. I gave it some time and by the next day, there was fresh ice!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandy from DANSVILLE, NY
- Parts Used:
- 5304511738
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Fridh light bulb blew
Got sent the wrong bulb 3 times had to pay for the three bulbs 75 dollars each Sent pictures of right bulb still wrong bulb no refunds for 30 days I even gave them right part number. Found out that the part number on box but wrong bulb inside told them and they seem not to care ordered from another company still out 225 dollars
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie L from Eureka, CA
- Parts Used:
- 240338101
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Broken Plastic Edge
Easy peasey just slipped it in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wendy from OCALA, FL
- Parts Used:
- 240350608
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken Crisper Glass
Very easy. Watched a video on your site prior to getting the glass replacement. Removed the crisper drawers. Placed the glass in the front and placed it down. Took just a few minutes. Love your site and will come back again when needed. Thank-you.
Was this instruction helpful to you?
Thank you for voting!