36379282991 Kenmore Refrigerator - Instructions

i pulled the old gasket off, and placed the new one in place, starting at the corners. then i lined up the insert in the gasket with the gap where it is to go and ran my fingers along the gasket, pressing in with my thumb.

Tried replacing water valve since no water in ice cube tray. Exact part not available due to age of refrigerator, but I got the equivalent replacement part for $18. Mounting holes different, but I made it work. Also one connect on new one slip connect whereas both compression fittings on old valve. I put it back together and icemaker now works great.

Turned off the breaker to the fridge because I couldn't reach the power plug to unplug it . Use small flat head screwdriver to pop out the piece, disconnected the rubber prong connectors, inserted the new piece into the rubber prongs snapped it back into place. Flipped the breaker back on and prayed it worked. It did and I saved myself $120 service call.

I loosened the compression nut on the valve with my fingers and pulled the water line free from the valve. On the other end, I just pulled it from the hose clamp. Installation in reverse. Force the water line into the fitting on top, Slide the old nut over the line on the bottom. Screw the nut onto the valve. Reach inside the freezer and turn on the ice maker. Done. Before replacing the cardboard grill, you should vacuum the coils on the bottom, front and back. If practical, push it outside and blow it out with an air compressor or a leaf blower.

I had made a dry run at the repair after watching the instructional film provided by part select and it seemed easy enough.
The only problem was that i needed to use the electrical cord extender (provided) to adapt to my plug type. That presented a problm because it needed to be tucked up out of the way to allow the ice bin to clear. Just needed to be creative in how you wrapped the cord behind the ice maker unit before snugging the attachment screws.
Cranking out ice like crazy.

My husband thought he would have to set aside time on the weekend to replace the gasket. It was delivered and I unpacked it put it on and that was that.

I watched the video online, followed the instructions and within minutes had the part installed. The frig light was working once again! I will say the original switch was very snug and I had to do some very minor scraping of the plastic to get the new part to slide in.

Three easy steps, take off old part then all you do is tighten nut on one end of part and then just push other end of pipe down in slot. Did half to remove nut off the top end of tube very simple to do

First I removed the electrical plug from the back of the freezer that plugs into the icemaker. I then removed the two hex head screws that hold the icemaker to the wall of the freezer and removed the icemaker. I removed the plastic cover, which incidentally protects the gears, by prying it off with a srewdriver. I removed three small nuts(7mm) which holds the internal cam in place. I removed the cam by pulling it off the shaft. Once I got the part from you folks I reversed the procedure that I just mentioned, and put the icemaker back together. It works great. The part with shipping was around $16.00. A new icemaker was roughly $159.00. If I would have called a technician it would have cost around $300.00 to repair.

Remove the rear cover, shut off the water, removed the hose, unplugged the electrical connector, removed the screw holding the valve on. Removed the plastic tube going into the freezer and reversed the steps

ATTACH ENDS TO CENTER BAR. HOOK INTO SLOTS IN REFRIGERATOR DOOR.

put the gratefruit knife behind the old switch pooped it out pluged the new one in piece of cake 5min.even vacumed the dust off the coil

Lift the shelf off. Remove the broken pin from the slot in the door. Remove the broken end cap from the shelf - slides out with relative ease by just prying up slightly the rolled edge of the shelf where it snaps in. Slide in the new end cap. Put the shelf back in place. Literally took about 3 minutes.

Extremely easy repair, the hardest part was getting the old switch out. I used a pair of needle nose pliers to squeeze the tabs in and it came right out.

Took old gasket off put new on.

Gasket came well packaged so only ran hot water over it briefly and put it on.