59679219012 Kenmore Refrigerator - Instructions

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Freezer would get cold at bottom and some of the refrigerator. Took of freezer back panel and located freezer fan. Took a meter and saw power was getting to it, but not working. Removed fan and replaced with new on, working like a charm. Cold air was not circulating enough throughout the unit because fan was not working. It was not the thermostat or adapter control.

Popped out old gasket and popped in nwe one. This is where things get interersting, the new gasket
Does work as well as the one I replaced. I think the maganet is not strong enough. If anyone has had the same problem please let me know. This model ( Maytag- French door ) has been a lemon.

Took drawers out, inserted the rail and put the drawers back in and voila. Fixed.

Watched Partselect video of P-trap installation.Removed water line & back cover& disconnected wires to water solenoid .Removed old drain tube & old problematic rubber funnel. Used contact cleaner to clean rubber residue from drain line and used a little silicone to aide reassembly. Job went well thanks to video.

took the pantry drawer out removed track replaced and put on new door... very simple

The repair seemed simple, I just needed to remove the old bracket -- 4 screws -- and slip the new one on.

The tricky bit is that the roller bracket holds the weight of the fridge. So in order to make sure that the fridge did not fall over, and to keep the installation point off the ground so that I could align the screw holes, I needed to shim up the side of the fridge that I was working on.

To tap in the shims, I used a hammer and a spare chunk of wood. I ultimately used 3 shims, and kept tapping until the roller wheel could roll freely. Then I knew that the fridge was high enough. After that, it was pretty easy to remove the 4 screws, align the new bracket, and replace the screws. After that, in order to get the shims out I could just extend the foot brake as it was designed, and that lifted the fridge enough for me to easily slide out the shims. After that I just had to level out the fridge by adjusting the two feet.

Took the new door seal out of the box, layed it out as straight as possible heated it with hair dryer 4 1hour took the old 1 out by hand and replaced it with new one no tools needed 10 min job

I was easily able to find the part using the online search. I order the part and it arrived in about two days. Installing the part meant pulling out the two crisper drawers, emptying the shelf above the crispers, removing two glass shelf plates, inserting the new part, replacing the glass plates, replacing the food on the shelf and sliding in the two crisper drawers. All in all, about 3 minutes.

Removed door from slide bars with small nutdriver, pulled old gasket out of retaining slot, cleaned slot & area around it, pressed new gasket into place with fingers, relatively easy. Used hair dryer to make sure gasket was formed properly and contacted fridge unit eavenly.

replaced broked crisper pan with new pan

unplugged the unit pulled it away from the wall removed the lower panel removed the drain installed the new replacement . removed the wiring harness and replaced it with the new one replaced the panel and plugged back in

Took a putty knife and
Removed the old switch removed the spade terminals from the old switch and replaced them on the new switch and just pushed the new switch back in place

I removed the crisper drawers, glass shelf, and frame assembly to install the ladder hook. Before reinstalling the glass shelf on top of the crisper frame, I installed the center crisper rail.
Thank goodness for websites like this!

I watched the video provided on-line in your website, which was excellent. The information provided gave me everything I needed to change the board. I already had experience handling control boards and was aware of the static precautions; however, your paperwork was very good detailing how to program the new board. The only small problem I had was reinstalling the temp sensor in its bracket. The lead was very short. Other than that, all went well! The project took between 20 and 30 minutes.