79573063410 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sonya from VAIL, AZ
- Parts Used:
- AGU75188619
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The spring on the mullion door broke for the last time
This was an incredibly easy repair! 1 phillips screwdriver and two screws. Disconnect the small adapter, and you are good to go!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from MONTGOMERY, AL
- Parts Used:
- AGU75188619
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Spring broke on Mullion
Watched the video. Took the screws out, unplugged the connection and slid mullion off. Then plugged the new one in, slid it on and attached the two screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jodi from WINTER GARDEN, FL
- Parts Used:
- AEQ73110210
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
My ice maker wouldn't release the ice, nothing was frozen and the motor would just bind
I bought the ice assembly motor only, super easy to install, remove the three main screws, lift out assembly, detach the cable. Then remove the screws on the parts, lift the tape, redo everything in reverse and it works flawlessly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnny from MOUNT OLIVE, AL
- Parts Used:
- AJU72992601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Leaking
Swapped old one with new one. New one had extra plug not needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from GODDARD, KS
- Parts Used:
- AEQ73110210
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The refrigerator ice maker needed replacing
The only tool required was a Phillips screwdriver. I disassembled the old icemaker and unplugged the electrical snap in device. I removed the ground wire. Then reversed the steps in replacing the refrigerator ice maker kit assembly. It took slightly over 30 minutes to remove and replace the ice maker.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- shirley from ONALASKA, WI
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Light switch for refrigerator not functioning
Followed instructions online
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from BLUFFTON, SC
- Parts Used:
- ADX73550624
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Torn door gasket
Pulled old gasket off by hand. New gasket was easy to install by pushing it into molded cutout in refrigerator door.
Very satisfying to have no glitches in the seamless installation.
Very satisfying to have no glitches in the seamless installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from COUNCIL BLFS, IA
- Parts Used:
- MHL62691504, AEC72910002, AEC73597502
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broken sliding rails for vegetable and deli tray. Glass replacement for vegetable trays
Removed trays and replaced broken sliding parts and replaced glass
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eugene from ENCINITAS, CA
- Parts Used:
- AEQ73110210
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Ice tray cracked
Removed the old one and replaced with new just remember do your do diligence watch YouTube videos makes repair a lot easier
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Katherine from NEW PRT RCHY, FL
- Parts Used:
- MHL62691504
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Broken shelf for the vegatable bins
The glass was ordered correctly. The part was too big for mt refrigerator. I tried to send it back, but I got no reply. I tried cutting the glass to size and it shattered. I wasted 60.00 and im disgusted with your company.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JON from OJAI, CA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
INTERIOR DOOR ACTIVATED LIGHT SWITCH QUIT WORKING
1. Unplug the refrigerator (to avoid shock) 2. With one screwdriver pry open the switch on the side facing the door to a gap of about 1/8 inch 3. Insert a second screwdriver into the gap to press the plastic tab back slightly and this should release the part. 4. pull the part out and unplug it, you may have to pry back some small tabs on the sides, 5. Plug in the new switch 6. plug in the refrigerator the light should come on, if not tighten the connection 7. Insert new switch back into its slot, it should snap in place. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from TONAWANDA, NY
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
bad switch
The 2 minute or so video was not exactly matching the model that we had but the instructions were very good and important. The switch was a little difficult to get out from the side of the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Calvin from Northome, MN
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Light quit coming on when door opened.
Unplug from wall receptacle. Pry switch out with screwdriver while pushing on inner tab. Then disconnect electrical plug.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Ashland, MA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Lights didn't come on when door was opened
I have moderate to good mechanical skills, but getting the old switch out was a sizeable challenge. Since this switch suffered some damage during extraction, I was lucky to have ordered a new one to replace it. Reinstall took approximately 90 seconds. PartSelect saved me an expensive service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from IMPERIAL, CA
- Parts Used:
- AGU75188619
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken spring on flapper door
Unplugged the frig and removed two phillip screws on flapper door of left door... Unplugged the electrical connector and removed flapper...
Picked up new flapper and snapped electrical contractor together... Slid new flapper bar into place and inserted two phillip screws... Job complete in 15 minutes...
Picked up new flapper and snapped electrical contractor together... Slid new flapper bar into place and inserted two phillip screws... Job complete in 15 minutes...
Was this instruction helpful to you?
Thank you for voting!