79570339410 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Timothy from SUSANVILLE, CA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
interior light switch did not turn off light in ref
pried out old switch, disconnected wires ,placed wires on new switch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from MORGAN, TX
- Parts Used:
- AEQ73110210
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
ice would stick in 5 of the 14 cubes spaces from mineral deposits, then ice couldn't drop and water would not fill
was easy watching youtube video of how to replace whole ice maker, was only 3 screws, remove from the door, a couple of screws hold it to the flat piece, route the wires around the unit, connect the plug as installing it in the door, position it, and tighten 3 screws, that easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROGER from SCHELLSBURG, PA
- Parts Used:
- MJB62830601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door stopper broke
Installed new door stopper with screw driver on bottom of french door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from FORT SMITH, AR
- Parts Used:
- AGF80300702
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Replace water filter
Followed directions that came with the filter. Did remove the top shelf for easier access. Very simple and quick.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BG from WEATHERFORD, TX
- Parts Used:
- MHY62044106
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
I actually took a picture of the correct spring installation at a big box store that carried LG. I had called LG, but they said they didn't have any installation brochures, and to call a registered LG repairman. That was out of the question, since the repairman would charge $100 just to show up.
I looked at the picture I took. Used needle nose pliers and inserted one end. Unless the lady of the house is very strong, this should be handled by a man, because of the rigid spring. Once the spring was inserted into one side of the flap, I used the pliers to get the other end into the proper slot. Very easy, but the spring is very strong !!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lloyd G from QUEENS VLG, NY
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Light doesn’t come on when fridge door opens
Pulled fridge away from wall, unplug electrical connection, open fridge door, use knife to prize out door switch, pull off and replace switch from electrical wiring.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from WHITE BIRD, ID
- Parts Used:
- 4681JB1027C
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Blower motor out on condenser
followed detailed movie from Utube video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from ABERDEEN, WA
- Parts Used:
- AJU72992601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
Low water pressure which in turn led to no water and no ice.
Unplugged fridge, shut off water supply disconnected water supply from fridge. Remove screws that hold lower cover on back of fridge, removed screws holding valve assembly to fridge. Disconnect two electrical connections, remove black c-clip on out flow water line, lift fitting on outflow line side and pull water line off. Replace with valve assembly in reverse order
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from SHORELINE, WA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door switch would not turn on interior refrigerator light.
I had previously watched a YouTube video (do this first!!) on a similar Kenmore model so I knew what to look out for: (1) turned off power, (2) took thin putty knife to slip under outer lip of switch (most screwdrivers are too thick), (3) wiggled switch at front end to release the tab, (4) unplugged from the socket, (5) plugged in new switch, (6) popped new switch back into door, (7) turned on power. Voila !! Super easy. I couldn't believe it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from CLEARFIELD, UT
- Parts Used:
- AEQ73110210
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Ice Maker Can’t Rotate/Discharge Ice
First, remove power to the refrigerator.
To replace the ice maker you first have to remove the back mounting assembly, which ice maker is attached to.
Only three Phillips head screws need to be removed: 2 on the bottom and 1 on the back of the ice maker mounting assembly. Do not remove the two diagonal Phillips head screws holding the dispenser motor on the reverse side of the mounting assembly.
As you pull out the mounting assembly to the front you will see a connector on the top inside, which must be unplugged. A narrow standard screw driver will help the connector lock to release; slide the screwdriver tip under the connector lock clip and it will allow the connector to be unplugged.
Once the ice maker mounting assembly is removed and placed on a flat surface it will be self evident as to how to remove and replace the ice maker. The 1” tape might be needed during the cable re-routing process. However you can reuse the original tape required to be removed during the ice maker remove and replace process, if possible.
Reinstall the ice maker mounting assembly in the reverse order it was removed.
Apply power to the refrigerator.
Cycle the ice maker to Off and then back to On. It may take an hour or two before the ice maker produces ice because the temperature inside the ice maker must reach “0” degrees Fahrenheit before it will begin making ice.
Pull the ice maker
To replace the ice maker you first have to remove the back mounting assembly, which ice maker is attached to.
Only three Phillips head screws need to be removed: 2 on the bottom and 1 on the back of the ice maker mounting assembly. Do not remove the two diagonal Phillips head screws holding the dispenser motor on the reverse side of the mounting assembly.
As you pull out the mounting assembly to the front you will see a connector on the top inside, which must be unplugged. A narrow standard screw driver will help the connector lock to release; slide the screwdriver tip under the connector lock clip and it will allow the connector to be unplugged.
Once the ice maker mounting assembly is removed and placed on a flat surface it will be self evident as to how to remove and replace the ice maker. The 1” tape might be needed during the cable re-routing process. However you can reuse the original tape required to be removed during the ice maker remove and replace process, if possible.
Reinstall the ice maker mounting assembly in the reverse order it was removed.
Apply power to the refrigerator.
Cycle the ice maker to Off and then back to On. It may take an hour or two before the ice maker produces ice because the temperature inside the ice maker must reach “0” degrees Fahrenheit before it will begin making ice.
Pull the ice maker
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William L from SUMAS, WA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light didn't come on when the door was opened
I took a very thin bladed screwdriver and took the old part out -carefully.
The new part fit in quite easily.
The new part fit in quite easily.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from VICKSBURG, MS
- Parts Used:
- MHY62044106
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The Mullion Strip Spring Broke
Removed mullion strip with Phillips screwdriver replaced spring reinstalled the mullion strip all in about 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from EGG HBR TWP, NJ
- Parts Used:
- AGU74110903
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Fridge door wouldn’t shut
Took old door strip (spring broke) and installed new with spring It went well and was working in less than 5 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from DADE CITY, FL
- Parts Used:
- MHY62044106
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Left French Door would not close properly
Removed two screws from door and three locking brackets with a small common screw driver. Raised the bracket, slide in the spring, held down the bracket, installed screws and plastic covers. Less than 2 minutes. Easy application no problem with the new spring or ,mullion..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from BOWDOINHAM, ME
- Parts Used:
- ADQ36011715, AGF80300702
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
The hose that feeds the Ice Maker broke,right where it goes in the Fridge.
I actually didn't use what I got. Because there was all kinds of tubing coiled up in the door. We just fed the exsess all the way through the Fridge,and Bingo! It was done.
Was this instruction helpful to you?
Thank you for voting!