59679242016 Kenmore Refrigerator - Instructions

Just slipped it in. I think it's a very poor design.

First found U Tube video of my exact refrigerator, ice maker remove and replace. Many available, all are helpful. Watch several times. Once part arrived the repair went very smoothly. Only had some difficulty attaching the ground wire, had to loosen the auger motor to attach the tiny screw. Not difficult, just took a bit of time to get the angle on the screw correct.

I easily ordered the part. When it came in, I just shut off the water, disconnected the electricity, and followed instructions to remove shelving and drawers. Then removed the rear interior cover, removed the old water inlet valve and installed the new one. Just a couple moldex wire connections and the 3 water lines in and out. Don't know if this is still ok, but so simple a caveman could do it. Sorry Geico.

Looked online for instructions. I had to remove the shelves from inside the frig, then pop off part of the right inside back wall. The way the 3 water lines attached to the inlet valve was a terrible design. There are plastic little collars that need to be pushed back to release the water lines from the old valve, then when you install the new valve, you need to push them back to reattach the water lines. Once installed, one had a leak. No matter how hard I tried I couldn't get the little plastic collar to disengage. I couldn't push the line in further and I couldn't get it back out. Ended up cutting the line off at the valve just to get it out. Then had to cut out the piece that was still stuck in the valve. Tried to install it again and it leaked even more. Ended up putting the old valve back in and throwing away the $130 new inlet valve because there are no returns on electrical parts. Total waste of time and money ! ! ! Not happy to say the least.

Snap Out
Snap In
Yes That Easy!!

Once I took new gaskets out of carton
and put out on patio to warm up I removed old gaskets pressed in new gaskets which made a great seal
Job was easy and took no skill

last time i tried it right away after removing from shipping box.. relaxing with with hot air gun... was not to easy... this time i allowed gaskets to relax for a week on a flat surface. in a warm room.... took less than 5 minutes per door.... no hot air needed.... VERY easy.

Very easy. Just get hold of the gasket with your strong fingers and pull it out of the groove it is in. Clean the groove, I used Windex and paper towels. On the new gasket there are 2 wide areas on the vertical part. these must be facing toward you and on the handle side of the door. start at the tor center of the door and work the gasket in with your fingers outward to the corners then work on the bottom of the gasket in the same manner, then start on the vertical gaskets. when you think every thing is aligned take your thumbs and press very hard all around. You may have to repeat.

Got lucky ordered new ice maker then current one started working again ???????

watched video
took me less than 5min. to replace inlet valve.
an cleaned my frig at the same time that took me longer to do.

Took out ice maker. Then unscrewed tray after opening old turn motor clock panel and carefully detaching wires from socket(s) where needed. Put in and screwed in new tray with the new motor clock. Replaced wires into new sockets. Put the whole maker back into place. Makes great ice.

Open the existing cover and carefully with the thumb and index fingers, pry the cover at over the left pin and remove the cover. Place the replacement onto the right pin and pry the left placing it over the left and you are done.

With a small allen wrench, I was able to loosen the two screws to remove the door handle and replace the new on without any problems. A very simple operation.

It took longer to empty the glass shelf above the Crisper Bins than to replace the rail. Since the part simply snaps in place, no tools were required

Took the new kick plate out of the box. Snapped it into position. I have had a repairman for this refrigerator before. I would rather repair an appliance than buy a new one. I'm very proud that I thought to get a replacement part myself instead of calling my friendly repairman again. Saved a few dollars.