79570333410 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- JANET from GRAND JCT, CO
- Parts Used:
- AGU75188619
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The spring on the mullion was broken so the mullion would not open to seal the other door.
I am a73 year old woman. If I can do this, anyone can. Super easy. Just watch the online video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayde from SEMINOLE, FL
- Parts Used:
- AGU75188619
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Spring broken in door mullion
Took 2 screws out and disconnect wire and install new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from PENNSVILLE, NJ
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Switch stops working
Replace with new switch. this is the third switch i have replaced in 10 years. the only part, besides a light bulb, that has gone bad. obviously this is a problem with this model for Kenmore, or just poor switch design.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from NORTH AURORA, IL
- Parts Used:
- AGU75188619
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Removed old part.
Installed new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from MERRITT IS, FL
- Parts Used:
- AGU75188619
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old part did not seal properly
Read the reviews from other members and just did as they said. Needed a screw driver and the info from past persons review couldn’t have been easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from CASA GRANDE, AZ
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
door slight switch failed
Covered the sidewall with tape to protect. Pried the switch out with knife blade and removed electric plug with needle nose pliers. placed plug in new switch and pushed switch into the hole in the side wall. Took about five minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eugene from ENCINITAS, CA
- Parts Used:
- AEQ73110210
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Ice tray cracked
Removed the old one and replaced with new just remember do your do diligence watch YouTube videos makes repair a lot easier
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from CURWENSVILLE, PA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Door light switch, 3rd one I have replaced in 6 years made in China.
Easy install, small screwdriver under back of old switch push out and pull out with small pliers. unsnap the old plug and install new. YOUR DONE
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from HILLSDALE, MI
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replace switch
Read previous tips
Taped off area around switch to protect surface
Used putty knife to extract switch
Used screwdriver to separate connector from switch
Plugged in connector
Pushed switch assembly into opening
Removed tape
Taped off area around switch to protect surface
Used putty knife to extract switch
Used screwdriver to separate connector from switch
Plugged in connector
Pushed switch assembly into opening
Removed tape
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from TONAWANDA, NY
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
bad switch
The 2 minute or so video was not exactly matching the model that we had but the instructions were very good and important. The switch was a little difficult to get out from the side of the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from WARREN, RI
- Parts Used:
- AGU75188619
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Spring in the plate front assembly broke. Door plate assembly would not move into correct position, preventing door from closing.
Followed Youtube video provided on the PartsSelect Website:
https://www.partselect.com/PS12374439-LG-AGU75188619-PLATE-ASSEMBLY-FRONT.htm?Inventory=12374439&SourceCode=20&SearchTerm=LFX28979ST
Made installation of the new part a piece of cake. Easy peasy!! Took less than 10 minutes.
https://www.partselect.com/PS12374439-LG-AGU75188619-PLATE-ASSEMBLY-FRONT.htm?Inventory=12374439&SourceCode=20&SearchTerm=LFX28979ST
Made installation of the new part a piece of cake. Easy peasy!! Took less than 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Ashland, MA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Lights didn't come on when door was opened
I have moderate to good mechanical skills, but getting the old switch out was a sizeable challenge. Since this switch suffered some damage during extraction, I was lucky to have ordered a new one to replace it. Reinstall took approximately 90 seconds. PartSelect saved me an expensive service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from IMPERIAL, CA
- Parts Used:
- AGU75188619
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken spring on flapper door
Unplugged the frig and removed two phillip screws on flapper door of left door... Unplugged the electrical connector and removed flapper...
Picked up new flapper and snapped electrical contractor together... Slid new flapper bar into place and inserted two phillip screws... Job complete in 15 minutes...
Picked up new flapper and snapped electrical contractor together... Slid new flapper bar into place and inserted two phillip screws... Job complete in 15 minutes...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from GEORGE WEST, TX
- Parts Used:
- AEC73857402
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
rail that holds meat tray broken
remove all trays from refrigerator , remove screw holding rail and install new rail.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Angela from SAINT JOSEPH, MO
- Parts Used:
- AEQ73110210
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice tray was not rotating any longer
Took the old one out and put the new one in.
Was this instruction helpful to you?
Thank you for voting!