79570333410 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from JACKSONVILLE, FL
- Parts Used:
- AJU72992601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
replace leaking water inlet valve assembly
1. Shut off water to refrigerator. 2. Removed bottom sheet metal cover (6 screws). 3. Removed leaking water inlet valve assembly from refrigerator (1 screw). 4. Remove water inlet tube (loosen nut) and tube back to refrigerator (pull from water valve after remove cotter pin washer). 5. Detach two electrical wire harnesses. 6. Install new water inlet valve assembly to refrigerator (1 screw). 7. Replace both water tubes to water inlet assembly. 8. Re-attach both wiring harnesses. 9. Turn water to refrigerator on. 10. Check for leaks. 11. Re-attach bottom sheet cover (6 screws).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debbie from Waltham, MA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Remove and replace light switch
Video makes it look easy. Kenmore refrigerator does not have "groove" along the right hand side of switch that allows for pushing down on release. Used a thin screwdriver to get under to push while holding switch edge with pliers. Kept slipping. Tape sides to avoid scratching inside of refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from LAKE WYLIE, SC
- Parts Used:
- ADX73550624
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The factory door gasket was split and needed replacing
I pulled the gasket off and installed the new one. It was very easy. All I had to do was to push the new gasket in place in the grooves in the door. The gasket I received was identical to the one I replaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tiziana from WARWICK, NY
- Parts Used:
- AGU75188619
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
My nephew accidentally forced the door closed last year, which resulted in the door having to be re closed manually folding back the flap. Ugh!
Unscered 2 screws, unplug electrical connection under the screws, slide her flap into grooves, realign screw holes , and rescrew in. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wallace from AUSTIN, TX
- Parts Used:
- ADX73550624
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
torn right hand door gasket
So easy I couldn't believe I'd done it so quickly. Two minutes from start to finish. Pull the old one off and press the new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maurice from SEATTLE, WA
- Parts Used:
- AGU75188619
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Door Mullion Spring
Had to buy the entire door mullion because the spring broke, wasn't happy. Got the new part very quickly and it was a new replacement part number. Somewhat tentative. Took it out of the box and looked it over. No spring! Groan! Thought I got the wrong part. Flipped the bottom hinge and it snapped open, no need for a spring! Two screws, disconnect the wire harness, throw away the old, get new, connect the wire harness, connect hinges, put in two screws! Super easy. Watch the video for some pointers along the way.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles R from FAIRFAX, VA
- Parts Used:
- MHY62044106
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Spring on door closer broke
Found the broken spring; matched it with parts diagram. Googled for sources via part number. Selected this site because it had best deal - price, availability, shipping. Part arrived as predicted; installed it in 2 minutes. Job done. Door now works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from JOHNSON CITY, TN
- Parts Used:
- ADX73550624
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old gasket had split.
Used putty knife to pry out the old gasket, pressed new one in place. Very easy, done quickly. About 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pauline from CUTLER BAY, FL
- Parts Used:
- AHT73554102
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Broken glass shelf
I was unable to replace the shelf (no assembly required) because I was sent the incorrect part even though I gave the model #,
serial # and exact description and measurement to the agent to whom I spoke. Even worse, I was told that I was responsible for returning the part at my expense. Rather than risking getting another incorrect part I will have a replacement plexiglass made to fit my shelf.
serial # and exact description and measurement to the agent to whom I spoke. Even worse, I was told that I was responsible for returning the part at my expense. Rather than risking getting another incorrect part I will have a replacement plexiglass made to fit my shelf.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- H Bartlett from JENSEN BEACH, FL
- Parts Used:
- ACQ86549505
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Remove and replace cracked crisper drawer cover frame
1) Remove three drawers and items sitting on glass shelf.
2) Remove glass shelf
3) Remove entire crisper plastic unit from refrig.
4) Unscrew 6 screws holding uprights with a philips head screwdriver.
5) Remove top frame and replace with new frame.
6) Replace 6 screws and tighten them.
7) Replace entire frame in refrig and replace 3 drawers and glass shelf.
8) Done
2) Remove glass shelf
3) Remove entire crisper plastic unit from refrig.
4) Unscrew 6 screws holding uprights with a philips head screwdriver.
5) Remove top frame and replace with new frame.
6) Replace 6 screws and tighten them.
7) Replace entire frame in refrig and replace 3 drawers and glass shelf.
8) Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from LUDINGTON, MI
- Parts Used:
- AEQ73110210
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
ICE MAKER JAMED WOULD NOT ROTATE
REMOVED 3 SCREWS AND OUT IT CAME UNPLUG THE HARNES AT THE TOP YOUR NONE
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorothy from KINGMAN, AZ
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Bad Push Button Switch
I followed the directions! It was so easy that I bought another switch for my sister's fridge (same as mine). Her light was out too!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from KATY, TX
- Parts Used:
- ADX73550621, ADX73550624
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Needed to replace door gaskets due to tear and sweating between doors
It was easy; just pull off the old gaskets and press in the new. Used the putty knife to help set the new gasket, but was really not needed. The flat shipping pack helped because there were no kinks or folds to worry about.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from RICHMOND, TX
- Parts Used:
- ADX73550621, ADX73550624
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door gaskets on French doors needed replacement.
Saved me $175.00 to $250.00 for an appliance repairman to come to my house for this. Absolutely simple to do. Pull gasket from right side door, no tabs or screws. Replace with new gasket, simply push new in by hand. Left side door needs two screws removed from’ flap. Now, gently bump the bottom of the flap to lift the flap up only three inches or so. Remove the electrical connection tab under the metal plate that the two screws secured. Now, repeat what you did on the right side door. Simple!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from TUCSON, AZ
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Refrigerator light would not reliably turn on when the door was opened.
Switched the refrigerator circuit breaker to off. Put tape around the switch to prevent scratches. Wedged the putty knife into the right side of the switch and pried up.the switch and connector popped out. Removed the connector from the old switch and connected it to the socket in the new switch. Stuffed the new switch and connector back into its home. Switched on the circuit breaker. Now we have light in the refrigerator with every opening!
Was this instruction helpful to you?
Thank you for voting!