25331438104 Kenmore Refrigerator - Instructions

I had to loosen the screw holding the mounting block and increase the hole size to fit the screw on refrigerator

Unplugged fridge. Removed freezer shelves and unscrewed and removed plastic shelf brackets. Removed the lower rear panel. Removed the bin for ice. Removed the 2 exposed upper rear panel screws. At this point I was able to flex the panel quite enough to access the fan motor. Carefully plugged the fridge back in and turned it on long enough to verify the existing evap. fan motor was not running. Powered off and unplugged again. Removed the fan and it's support assembly, and replaced with new. Had to cut the wires and splice and crimp with the provided wire nuts since the plugs in this model were different. Powered on fridge to check fan function. Reassemble and go home looking' like a hero! Saved my BFF a couple hundred bucks.

The evaporator coil is behind the freezer. Remove the rack that makes the shelf and remove two 1/4” hex head screws I the back of the freezer to access the coil.
I used a hair dryer to melt the ice off the coil.
The thermostat clips on the refrigeration pipe to the coil. Remove the old thermostat and cut the wires at least a few inches from the thermostat. Clip the new thermostat on the pipe and strip about a 1/4” of the wire ends. The electrical connectors (provided with the new part) must be crimped to connect the wires.

Just snapped the item into place.

This was so easy it took longer to open the door than it did to install the rack. WOW. Nice to see something fits without messing with it. Thanks.

had it done in 5 seconds!!

Super easy it took no more than 5 minutes to replace the fridge door racks. Starting from opening the box when it arrived to closing the fridge door with the new racks in place. no tools needed, except a knife to open the box.

The switch prevented the door from closing about 5 years ago. So I just taped the switch down, and lived without a fridge light for the last 5 years. Painful! And wasteful (food spoiled because we couldn't see it.) Thought I was out of luck, assuming light switches were all the same, got fed up again, and pulled out old switch,,and searched the net for the part number, and just started calling the manufacturer. I got this website after no luck in calling, and took the step to order...and in no time, got it replaced, and we cam see now! It feels like we got a new fridge!

replaced it

I removed the door actuated light switch with my index finger and thumb on my right hand. I then removed the two wires from the switch. I noticed that the new switch had different look to it,I think Frigidaire must have had a problem with the original design of the switch. Reassembly was just replacing the two wires and putting the new switch in place, and no more door closing problem.

take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .

Had my 3 year old remove the 4 screws to holds the carboard in place. Pryde the old fan blade off with a screwdriver. slid the new fan blade on to the shaft then my 3 year old put the screws back in.

My husband watched the video on your website and found it very easy to do the repair. The repair company that diagnosed the problem wanted $210 to do it. The part I ordered was under $20, and after he installed it the refrigerator has been working great. We would highly recommend your site to anyone who needs to fix anything!

When my side by side Kenmore refrigerator quit keeping the top half of my freezer and refrigerator cold I called Sears to see how much it would cost to get it checked out and fixed. Bottom line it was going to cost minimum $65 (which was just for him to come out) to $250 on up depending on what the problem was. So i decided to "do it myself"! I took it apart and within a few minutes figured out that it was my evaporator fan. So I went to sears to order the part based on the part number and with shipping and handling it was going to cost $125. While at sears I got on one of their computers and quickly looked up Kenmore parts and partselect.com came up and I quickly found the part for $62 and I chose overnight delivery and spent a total of like $83. When my part arrived I realized that the wiring/plug ins didn't quite match up. So I got online and went to their website and found a video for "do it yourself'ers" like me on how to splice the wiring to make it match. It took me about 20 min to splice the wire and put my refrigerator back together and IT WORKED! Easy easy easy and I saved moocho bucks! Ill never pay a repairman again. Oh and by the way, I am blond! :-)

Exactly as the video showed, except I had to take the evap coil cover off and use a hair dryer to thaw it out. It was still frosting up too much, so I ordered the thermostat as well. Both were really easy, once i saw the location of the defrost timer and the thermostat. Thanks for the great site, prices that put the big store to shame, and the good video too!