3639517912 Kenmore Refrigerator - Instructions

A friend had no problem getting the new ice maker in. But then the problems started. The ice maker works great. But when the water fills the ice maker it squirts water onto the side of the freezer and ice sickles form. So we watched and decided the hole was too large so used a piece of plastic. That helped to cover the hole. But some water is still entering the freezer and not all going to the ice maker. The only other thing we can think to try is to use epoxy to try to close that place. A simple job has turned into a big headache. I wish they made the ice maker like the original one.

ordered the replacement ice maker. what I received was not an exact fit appication. I had to alter the screw holes for the mounting brackets. I had to use an extension cable (provided) to connect the the fridge. The point where the two cables were connected resulted in a cable that was not only unflexible but too long and I had to alter the ice maker unit to make the cable fit. I am still not completely happy due to the ice maker inconsistancey. Sometimes we have ice sometimes not. In fact, I had to take the whole unit out again today because tow cubes became lodged in the tray and would not allow the tray to fill which resulted in no ice for quite sometime. So, right now I am not too thrilled with the replacement part I received.

i did every thing according to instructionwhich was simple but it did not cover how to use the extension electrical plug-in and where to put the extra cord so the tray would go back in

The parts were here the next day. After removing the old ice maker it was a simple installation using the adapter cord furnished. It took about 15 minutes. You have to work with the cord some to get it to fit behind the ice maker, but it does fit. The ice maker started up immediately & works great.

I ordered the replacement from you guys, got the new ice maker and the plug had an adapter, but it wouldnt fit in with everything. So I cut the plug off my old ice maker and put it on the new one and it works just fine.
thanks for everthing P.S. i got the ice maker from you for 109.00 and sears wanted 130.00 for it
good stuff good deal.

Removed front cover, removed rear cover careful to note position of spring assisted parts, used pliers to unscrew auger rod end cap, removed and soaked in Lime Away fixed and movable blades. Reassembled using diagram on website for guidance.

Used the nutdriver to loosen two screws, life out ice maker, disconnect electric plug and put aside. Placed the new icemaker on the loosened screws, plugged in electric connector and tightened screws. Used small level to verify that unit was level.Waited about two hours for first cubes to be released into tray - has been working fine since!

Before disassembling the parts need to replace, I use my digital camera to get all the different angle of the item so I have the full reference to asswmble the new one

My husband took the old icemaker out before the new one came in. When the new one arrived, I installed it in less than 10 minutes.

Removed the Ice maker from the freezer because the light was not on. Disassembled ice maker, found printed circuit board had shorted across two posts because the board was black in that area. Bought new ice maker assembly, installed in less than five minutes, making Ice fine.

It took longer to remove the ice bucket and frozen food than it did to replace the ice maker. Remove one screw with a 1/4" nut driver, slide outward and remove plug. transfer water tube to new unit. plug it in, slide into rear slots and install one screw. Replace ice bucket and frozen food, shut the door and hear ice falling in about 30 min. Easy job! Great product! THANKS MJS

Loosened 2 screws unplugged cable. Plugged in cable adapter on new unit. Plugged in to receptical, hung on 2 screws, tightened 2 screws. Done

The part that I needed was no longer availabe on other sites. Found Partselect and they had the solution, only took 4 screws to replace auger-bucket assy now ice dispenser works good as new!!

removed broken rail and replaced two screws and the job was complete...took longer to clean the botom of the refrigerator than replace the part

Removed the ice from tray and removed screws from face of ice bucket. Reinstalled screws and face on new ice bucket. Inserted new ice bucket in position.
That's it all done.