36378477896 Kenmore Refrigerator - Instructions

Installing the part repaired the fridge and freezer immediately.

First I observe that the compressor motor is running since the freezer is cooling. The purchase of the condenser fan is initiated and when the part arrive it is just easy to reinstall the replacement condenser fan.

The problem on the front of the freezer door remains hot to touch and the compressor runs for a while and stop. The freezer is cold but still could not freeze the water. Inspection of the condenser fan reveals that it is not running. The order for the condenser fan from PARTSELECT came in a few days. Cleaning of the condenser of lint was first done and the process of removing the defective fan is just easy so with the installation.

The refrigerator as of now is running in perfect condition!

Removed the 2 drawers and then the glass shelf.
Positioned the drawer slid and tightened to rear screw and the front screw.

Replaced the shelf and the 2 deawers.

What's the big deal? Any 78 year old woman can do it.

I removed the condenser cover removed old fan blade defrosted the condenser section installed new blade and reassembled

my freezer quit freezing, it would freeze for one day, thaw the next, so I went online, found PARTS SELECT, LOOKED UP MY MODEL #, come to find out it needed three parts to keep my freezer to freeze, first part was a thermistor a small PART took me longer to remove all the covers, and shelving, PULLED THE OLD OUT, CUT THE WIERS TO SIZE, AND REINSTALLED, IT WELL! THAT WASN'T ENOUGH THE FREEZER STILL DIDN'T FREEZE IT THOUT IT WAS A COOL WORMING OVEN, HAD TO INSTALL THE THERMISTOR I, SO I DID, TEN MIN, NOW I THOUGHT THAT WAS IT BECAUSE IT STAYED FROZEN FOR A WEAK, HAVE YOU EVER EATEN SOUPY ICE CREAM? SO BACK TO PARTS SELECT, THIS TIME I BOUGHT ONE MORE PT, THE RUN CAPACITOR, FIVE MIN, THAT/S ALL IT TOOK TO INSTALL. I DID NOT KNOW AT THE TIME YOU NEED THE THREE OF THEM TO RUN THE FREEZER ONE TO KEEP THE TEMP., ONE TO KEEP THE FAN RUNNING THE WAY IT SHOULD, AND THE THIRD TO MAKE SURE THE OTHER TWO KEEP RUNNING. NOW I CAN SET IT AT 4- 5 AND. FREEZE.

Other than having to bend the bracket 90 degrees it was an easy install.

turn breaker off first then use thin blade screwdriver and plastic pry bar to remove light socket and switch there was plenty of wire so work was easy to install at both ends

unplugged the old valve and disconnected the water line, then reconnected water line on new valve and plugged it in. It was an easy process but unfortunately that did not fix the problem. It is the ice maker it self so I will be ordering a replacement ice maker.

First removed the two screws that holds the old ice maker in place. Unplugged it. The freezer compartment was too narrow to allow the unit to slide out or turn in any other direction. Had to also remove the two front screws from the left side ice bin track and swing it down. The door opening was also too tight. Scratched the plastic door jamb putting the new unit in but other than that all is well and functioning well.

thats what I did is remove the teo screws and took the old single outlet valve out. And put the new one in and put the screws back in. First turned off the water and put the water back on after I was threw and no leaks.

After determining that the ice maker on this relatively new refrigerator would make ice cubes if it received the proper amount of water. Ordered the valve and received in a couple days. Using a nut driver, removed the cardboard cover from the back of the refrigerator. Removed one screw holding the valve bracket to the fridge and removed another screw holding the water supply line and the water line to the ice maker in place. Pulled plug on fridge and removed 2 wires from valve. Removed inlet and outlet lines from old valve and reversed the process installing the new valve.

First i removed everything from the bottom shelf, removed the glass, then removed the entire bracket assembly. Then removed the front metal strip to expose the front mounting screw, then removed the rear screw. Installed the new part and reversed the procedure.

Had to defrost a bit and then was able to remove rear freezer panel by simply removing the 2 screws holding it in place.
Old motor easily removed from its mounting bracket. and replaced with the new. Had to use the two wires sent with the motor. I clipped off the male connectors and joined them with wire splicers to the black and red wires clipped from the old motor. Then reinstalled.
The replacement motor works great. I was afraid the old fan blade might not fit but it slid on perfectly.

Remove ice maker out of fridge; remove 3 screws
replace defective part re-install all components 30 minutes later " magic ice again. Very easy repair most important low cost. Thanks "Parts Select"

Replacing the new part wasn't hard, just very time consuming and frustrating. I had to remove two-thirds of the shelving of refrigerator as broken drawer slide was on the bottom and I had to have room to remove old and replace new. Of course, then I had to CLEAN all the drawers and shelving before replacing them and then, because they were fresh and clean, I had to remove the other third of shelving and wash and replace it. So, it was an hour-long or more time. I love your business, and had no idea I could get so many parts for old applicance and replace them myself, and I am a 70-year-old woman! This was the 2nd time to use your site and I will return to it again when needed. Thanks for prompt and reliable service and a site that makes it easy for a neophyte like me to find the broken part ! Keep up the good work.