3639522681 Kenmore Refrigerator - Instructions

1. Put all perishable food into ice chest. Empty door shelves.
2. Remove top hinge cover with Philips screwdriver.
3. Supporting door, remove top hinge attached by two hex screws.
4. Lift door off bottom hinge.
5. On bottom of door, unscrew the hex screw holding the broken plastic cam.
6. Loosen the second hex screw enough to free the broken cam.
7. Replace the cam and tighten the hex screws making sure the opening of the cam lines up with the hole under the door.
8. Snap off plastic grill at the bottom of the refrigerator.
9. Remove bottom of the two hex screws holding the bottom hinge tot eh refrigerator body.
10. Loosen the second screw enought to rotate the hinge upsidedown. Tighten the screw again.
11. Now the rivet bottom is exposed so as to facilitate drilling it out to remove the broken cam.
12. Loosen the hex screw again and turn it back rightside up. Reinstall the bottom screw and tighten both of them.
13. Using an appropriate size bolt, lockwasher and nut, install other new cam.
14. Reinstall door reversing steps 1 to 4.
15. Don't forget to return the food to the 'fridge, by the way!

- Remove drawer and cover being supported by this slide. - Remove front and back screws with the screw driver. - Replace the above removed screws using the new slide. - Replace drawer and cover. DONE

Remove glass shelf. Remove slide (2 screws). Replace with new slide. Replace glass shelf. Done.

Removed the old, screwed in the new. Very easy, thanks for the video.

I glued the old rail back together twice prior to resorting to ordering the the replacement drawer rail from parts direct. Don't bother glueing the old parts, just buy a new one. Keep the screws from the old drawer rail as new screws are not shipped with the replacement rail. Only took 10 minutes to replace the rail needing only a phillips screwdriver. Good as new.

Remove broken rail by unscrewing two phillips screws
Discard broken rail
Hold replacement rail in place with left hand, tighten phillips screws with standard phillips screwdriver.
Wash scratch marks off bottom of fridge caused by drawer sliding on bottom of appliance
Slide veggie drawer into place, smile at wife, receive praise.

Removed the top hinge cover held by one screw. Removed the top hinge held by two screws and them lifted the door up and off the bottom hinge. Laid the door on the floor and replaced the cam piece from the kit on the bottome of the door. That required removing one screw and losening another. Removed the lower hinge (two screws) and replaced it with the new one in the kit. The lower hinge includes the other cam piece. Lifted the door onto the lower hinge and then replaced the top hinge and cover.

My husband took out the old icemaker in about 5 minutes. The new icemaker was a perfect fit even though the refrigerator was >10yrs old. The only difficult part was the plug extension that was needed so that it would fit into an older appliance. The part was included, it just made the cord about 3 inches longer than it needed to. After working with it for about 20 minutes we were able to fit it on the back side of the icemaker. Now it works great!!

The plastic door closing cams had broken after 17 years of use. It was tricky figuring out how the new cams fit as the old ones had disintegrated. Also you need 2 cams - not one. I first ordered only one. A detailed parts diagram would have helped. First unscrew the top door mount cover and then the top door mount. The fridge door then lifts up and off the lower door mount. Next is the hardest part - drilling off the old pop rivet which held the lower cam. The lower door mount had to be removed to get at the underneath of the pop rivet, and a bench vise was handy to hold it as I drilled off the old rivet. Then you need small stainless steel nut and bolt and split washer or lock nut to replace the rivet. Next unscrew the old upper cam from the underneath of the fridge door and replace. The large hole in the cam goes through the door hinge pins. The two plastic cams should interlock in a way that makes the door swing close. Anyway, now the door works fine.

Same problems as already described .... door would not close, plastic bits on floor, angry, ready to throw-out 15 year old “dog” and blow at least $1,000 on a new appliance!

This repair is dead easy. Remove the two bolts holding the top hinge and lift off the entire door. Don’t be surprised if the original Riser Cam has virtually disintegrated, mine was a wreck. Remove two bolts that retain the old flat metal “shim” and fiber “gasket”.

Fit new Riser Cam and re-use old shim and gasket. Replace door on dome-shape bottom hinge mount and then re-fit top hinge.

If in any doubt order new shim and gasket along with the new cam riser. Or, do as I did, and “manufacture” either of these parts from scrap material found in the workshop ....

First I removed 2 screws on each slide, removed the broken slide, replaced each slide with 2 screws. Done.

Please note that I did this repair 2 times before and it was very easy, it took me longer to get the stuff out of the refrigerator door.

But this time the existing upper and lower cams broke, and the lower part of the door was making contact with the screw that holds the lower cam to the lower support bracket damaging the head of the screw.

Now I could not use a screw driver and I had to use a wrench and a vise grip to hold the round screw head (not easy), and then replace the screw and nut.

I had to insert 2 flat washers under the lower support, to separate the door an additional 1/32 from the ref. base to accomodate the fact that the door gasket had lost its regular shape in the lower part of the door (I discover this when I dismounted the door).

Then I removed the damaged cams, replace them with the new ones and now it is working ok.

Manny

I learned from previous descriptions. Most important is there are two cams so order two. Second is that the door can be blocked from the bottom so the door doesn't have to be unloaded if you are careful. Remove the vent cover. Raise the door as high as possible while closed then block it from dropping down. I used wooden blocks. Remove the lower hinge and bracket on the bottom of the door. Put everythng back and you're back in business. A kit with both cams, spacers, and screws with diagram would have been nice to have.

I unscrewed the broken slide rail and screwed in the new one. Voila!

Ordering was easy and delivery was fast. BUT, the parts I received were not exactly the same as the ones I was replacing, even tough I certainly used my fridge model number when ordering the parts.

As a result the assembly is awkward, one of the rails did not fit and had to be cut half an inch shorter or so (there was some cover on the back of the fridge which prevented the rail from installing).

The rear mounting holes for all four rails also needed to be drilled anew.


The old drawer does not quite match the new rail either.

Overall I am not impressed. But to the partselect credit - the fridge is fairly old, 12 years.