10651134213 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Judith from RIDGWAY, CO
- Parts Used:
- WPW10515057
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
LED light in freezer not working
Unplugged frig. With flat head screwdriver, removed light module and unplugged. Installed replacement module and snapped back into place. Replugged frig.
But did not work!! Repeated steps 2x, but no change.
Had been told the frig LED light was the same module as the freezer, but that is not the case. I had hoped to try the new module in the frig. So, back to square one and since I installed the new part, can't return!
But did not work!! Repeated steps 2x, but no change.
Had been told the frig LED light was the same module as the freezer, but that is not the case. I had hoped to try the new module in the frig. So, back to square one and since I installed the new part, can't return!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allen from HOUSTON, TX
- Parts Used:
- W10873791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker not making ice and dripping water
This is an easy fix. The hardest part was just determining which part to replace. But the Q&A's for the ice maker from this site steered me right. And their video on how to install was easy to follow. The only difference I found was my Whirlpool had only 2 electrical connectors instead of the 3 in the video. I finished the job in about 15 minutes so everything in my freezer stayed solidly frozen.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from MURFREESBORO, TN
- Parts Used:
- WPW10515057
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Used a flat head screwdriver to pop the old light out.
Plugged the new one in and snapped it into place. Only other need is a lantern or someone to shine a flashlight over your shoulder since the old light is, presumably, out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from WEST PALM BCH, FL
- Parts Used:
- W10873791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Icemaker not making ice
Simple to replace. 6 screws out. Unplug connections... Plug back in, replace screws.
Unfortunately still not making ice. Will try fill valve replacement.
Unfortunately still not making ice. Will try fill valve replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jessica from WILLIAMSBURG, VA
- Parts Used:
- WPW10225581
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Part went bad the freezer was freezing up and refrigerator not getting cold
I pulled off the panel covering the part in the freezer cut and stripped the wires. Used crimper and connectors put the new part on put the wires band panel back on and plugged the refrigerator back in. Everything works just fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from BOULDER, CO
- Parts Used:
- W10873791
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Ice cube tray had a loose part hanging down
Did my homework.
Consulted Utube
Bought the part
Installed
Consulted Utube
Bought the part
Installed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from EDENTON, NC
- Parts Used:
- W10873791
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
My ice maker would only freeze for a short while, after unplugging it for a few hours it would begin to make ice again only to stop after a few trays
The repair went great, however, I had someone to put the part in for me.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from COLONIA, NJ
- Parts Used:
- W11037957, WPW10248011
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Socket set
Bottom plastic door cam on side-by-side frig worn, and door stop bracket broken.
1. Removed 2 screws on top hing.
2. Easily lifted door and place on table.
3. Removed set screw for door cam.
4. Removed stop bracket.
5. Reversed steps 4 thru 1.
When tightening top 2 screws, make sure door gap is consistent and top of frig door aligns with the top of the freezer door.
NOTE: The lady at PartSelect who helped me with my order was great. Took the time to verify my parts. Prior to this I had bought the part from a nearby appliance parts store. They sold me the wrong part, even though I showed them a picture of my model number plate b4 ordering. In the future, I will always go to PartSelect for my appliance part purchases.
2. Easily lifted door and place on table.
3. Removed set screw for door cam.
4. Removed stop bracket.
5. Reversed steps 4 thru 1.
When tightening top 2 screws, make sure door gap is consistent and top of frig door aligns with the top of the freezer door.
NOTE: The lady at PartSelect who helped me with my order was great. Took the time to verify my parts. Prior to this I had bought the part from a nearby appliance parts store. They sold me the wrong part, even though I showed them a picture of my model number plate b4 ordering. In the future, I will always go to PartSelect for my appliance part purchases.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Del from LAS VEGAS, NV
- Parts Used:
- W11035841
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Ice maker doesn't function
The wire bundle under the left lower corner has 8 wires of which 5 were chaffed and broken due to operation of the door and poor design. Remove the kick panel to expose the bundle, remove hardware holding the bundle to allow room to strip and splice the wires. Ice maker works fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- J. David from BRENTWOOD, TN
- Parts Used:
- WPW10350564
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Capacitor shorted out due to power surge.
Access back of unit, lower left corner. Remove wire capacitor retention clip. Unplug cold capacitor, plug in replacement, reinstall wire retention clip, test.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from STATEN ISLAND, NY
- Parts Used:
- WPW10225581
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Freezer work perfectly, Refrigerator Stopped getting cold, water line froze, there was ice Forming around the condenser in the bottom of the refrigerator behind the drawers
Freezer worked great, refrigerator stopped getting cold and lots of ice formed around the condenser on the bottom of the refrigerator.
First I had a serious ice issue, ice build up around the bottom of the refrigerator and all through the cold air vents, condenser and cooling fan. I unplugged of the fridg and let defrost over night. I also took all the cold air vents out and cleaned them.
Then I followed the switch install video very simple switch install. Now the Refrigerator works Great nice and cold.
First I had a serious ice issue, ice build up around the bottom of the refrigerator and all through the cold air vents, condenser and cooling fan. I unplugged of the fridg and let defrost over night. I also took all the cold air vents out and cleaned them.
Then I followed the switch install video very simple switch install. Now the Refrigerator works Great nice and cold.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from Albuquerque, NM
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
lights wouldn't come on/work in refrigerator
Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jay from WOODWAY, TX
- Parts Used:
- W10873791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Not making ice
First turn off the ice maker. Then there's four screws in the very back you remove pull out the cover. There's hex head 516 bolts maybe quarter inch that hold in the ice maker unplug the ice maker reverse process
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from MESQUITE, NV
- Parts Used:
- EDR1RXD1
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
ice container bin cracked and had a hole in it.
Took it out of the box. Emptied the ice out of the broken bin. Slid the new one in and all done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from WEST JORDAN, UT
- Parts Used:
- WPW10238100
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Valve leaking water
Unhooked water line from house to fridge then unbolted valve from fridge body then removed plastic water line from fridge to valve by pushing in on pex release tab then reversed process with new valve. Works like a charm. No more leakage. Wood floor is dry and Happy!
Was this instruction helpful to you?
Thank you for voting!