10651136210 Kenmore Refrigerator - Instructions

I took off the broken tube and attempted to order a new one with the confusing we sight at parts.com- after 3 attempts I finally got the right part with help from the operator at parts . Com( nice and helpful) but had to ship wrong parts ( the 2 wrong ones) back. The parts were of good quality and we're not hard to put on

Took the old one out and put the new one in

I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.

The new bin slid right into the required slot

It was easy. Took the broken door bin out and snapped the new one in. Good as new!!

I would like to add that I originally ordered the wrong part, was able to return for refund minus return shipping. Would recommend calling to order if you're unsure of the right part. David helped me the second time around. He was friendly and knowledgeable and the right part was ordered and sent.

Checked a video on YouTube and found questions and answers to this concern.. All lead to the compressor capacitor. Entered part # on your Website. Capacitor come right up and also suggested a Start Device. I ordered both parts as I was not sure if these parts would fix my problem.
R/R rear panel, found Capacitor and replaced it... Compressor came on and refrigerator operated correctly after defrosting Evaporator coils..

Took off panel in back and located part, removed it and installed new part

Removed existing fan. Access wasn't too dificult. Motor access was easy to access and remove. Disconnected old fan and the replacement part fit perfectly. Runs perfectly.

Turned off the power removed light by hand no tools required unplugged 2 wires. Plugged in the new light snapped it back into place. Turned on the power.

Remove the ice bucket and check that the auger that turns in the ice bucket is free to turn. Cover the open freezer with cardboard or whatever to retain most of the freezer temperature. Remove the holder that supports the top of the motor shaft. Check the splines on the upper part of the motor shaft and also check the seal under the holder. Open the access the door to the motor, remove wiring connector and unbolt the motor. Check the lower splines on motor shaft for condition, clean the shaft and apply new grease to the splines. Before installing, connect the wiring to the new motor, push the door switch in, press the ice dispenser arm outside the door to make sure the motor runs. If all ok, check the motor shaft for fit in the new motor. Be careful not to install the motor shaft too deep in the motor splines, otherwise there may not be enough spline showing on the top end to engage the auger. Bolt the motor in place, close access door and install the holder and ice bucket and make sure everything works. If there is not enough spline showing thru the holder to engage the auger, take pliers and pull the shaft up a bit. This seems to be a hit or miss fit on the shaft but you can adjust the height of the shaft without taking every thing apart again. That's all, not difficult at all. But do check parts and pieces for anything else you might need, parts wise, before ordering the motor by itself like I did. Shipping is high, so try to order any associated parts needed when you order the motor. By the way, This site are great to work with!

I use a Screw drive a Nutdriver set Needlenose Pliers and it took 30mins to fix.

Just follow youtube examples. Work in freezer. Troubles was I didn't fix the problem. Experts say thermostat is the best one to replace (53%). Anyway they are not always right.

with vidio

Opening up the Evaporator Fan section was a quick and easy job. After opening, I checked and removed the fan and looked at the grommet. The grommet on the fan was tight and secure and I could no longer hear the noise. I closed the opening. Something I had done while checking the fan grommet must have solved the problem. I have not hear the noise again!

Open the freezer door of your whirlpool refrigerator and locate the LED light under the ice cube maker. There are to notches that flat head screw driver will fit into allowing you to pop the light out of the housing. Disconnect the light from the wire connector and install new light. Pop new light back into housing and give yourself a medal. Operation complete.