10651593011 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dale from Flemingsburg, KY
- Parts Used:
- WPW10225581
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
It was not coming out of defrost cycle
First I installed a defrost timer, (the old timer had burnt out contacts in it) It seemed to work for a few days, then went back to not comng out of defrost cycle, I then installed a defrost thermostat. It seems to be working better than before. I found out that maybe I wasn't running it cold enough. So I turned it up colder. Now it works ok for 2 - 3 days, then I check the Temp in the freezer and its up to 6o. So I manually reset the timer and it works for 2 - 3 days. Don't know what to do now to fix it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andy from Lorena, TX
- Parts Used:
- WPW10190929, 8201515
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Heater on Ice Maker stopped working.
Repair was easy and producing ice within five hours.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from shady dale, GA
- Parts Used:
- WPW10189190
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
stopped cooling,the compressor would come on and shut back off.
pull the fridge out away from the wall and hope you have a long flex water supply hose.remove cardboard cover,oh yea unplug fridge first.unplug wire from the relay.flip the wire retainer off the relay and pry it away from the compressor.pull the 2 prong capacitor off and then reverse the steps to reasemble. skip the middle man at the local appliance shop.i waited 2 weeks for him to get the part and gave up.your reg shipping got it here in 2 days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debbie from Tyler, TX
- Parts Used:
- EDR3RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
water filter needed replacing
followed the instructions on the box
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tisha from Tucson, AZ
- Parts Used:
- W10408179
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
The water dispenser stopped working
Review the video on parts select. Do this first!
The actual repair took less than 30 minutes, including pulling out the refrigerator, performing the repair, and replacing the refrigerator.
Remove the screws holding the cardboard backing to the bottom rear of the refrigerator. Remove the screws holding the pump in place. Remove the electrical connectors and the water hoses from the pump. I needed the wrench to disconnect and reconnect the main inlet hose. Hook everything back up (the sizes of hoses and connectors are different). Replace the cardboard backing. Done!!
I would use Parts Direct again.
The actual repair took less than 30 minutes, including pulling out the refrigerator, performing the repair, and replacing the refrigerator.
Remove the screws holding the cardboard backing to the bottom rear of the refrigerator. Remove the screws holding the pump in place. Remove the electrical connectors and the water hoses from the pump. I needed the wrench to disconnect and reconnect the main inlet hose. Hook everything back up (the sizes of hoses and connectors are different). Replace the cardboard backing. Done!!
I would use Parts Direct again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Colleen from Chesapeake, VA
- Parts Used:
- 2198597
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Ice maker broke and not repariable
PartSelect was fantastic and I would recommend them to anyone! Online, Sears only showed a parts breakdown so I went to the service center. They could sell me an ice maker but PartSelect had the same ice maker for $35 less and it was on my door step the very next day! Mu husband plugged it in an we were on our way. You have been very easy to work with. I was amazed at the delivery time and I will use you in the future!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from E BRIDGEWTR, MA
- Parts Used:
- WPW10276348, WPW10276341
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
original parts--shelves had broken
simply slid out old damaged/taped up shelves and slid in the new ones i ordered,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from Richardson, TX
- Parts Used:
- 72017
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Scratches in Surface
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Bakersfield, CA
- Parts Used:
- WP2188664
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The edges of the Meat pan slide were broken.
I removed the glides under the edges of the meat pan, remove the old pan, put the new pan in and replaced the glides. I was very pleased with PartSelect. I ordered my part, and it arrived the very next day. I will definitely order my next replacement part thru PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Shakopee, MN
- Parts Used:
- WPW10190929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Ice stuck in mold. mold coating was peeling off.
Turn off water supply too ice maker and unplug the fridge power. using a nut driver remove one bottom screw from the bottom, near the front. The other two from the side atop the ice mold. (loosen screws and ice maker will lift up and off.)
I set the ice maker on the counter, snapped of the front cover by hand. using a phillips driver, remove two screws near the bottom corners.(they go through the circuit board into the ice mold)
circuit board in one hand, other end of ice mold in the other, slowly pull apart about 1 inch. remove the silver colored "on, off" bar at the end by snapping the retainer out of the ice mold. (the silver bar stays with the circuit board end)
Watch how the ice guide(white fingers stationary on side of ice mold) hooks too the ice mold on each end. swap ice guide to new ice mold, insert three guide pins on end into holes on the circuit board, while holding ice guide onto ice mold, watch rotation bar while inserting into motor.(it only splines one way.) when each piece is lined up, simply push together and reinstall two screws. snap circuit board cover into place. reinstall ice maker into freezer in reverse order.
I set the ice maker on the counter, snapped of the front cover by hand. using a phillips driver, remove two screws near the bottom corners.(they go through the circuit board into the ice mold)
circuit board in one hand, other end of ice mold in the other, slowly pull apart about 1 inch. remove the silver colored "on, off" bar at the end by snapping the retainer out of the ice mold. (the silver bar stays with the circuit board end)
Watch how the ice guide(white fingers stationary on side of ice mold) hooks too the ice mold on each end. swap ice guide to new ice mold, insert three guide pins on end into holes on the circuit board, while holding ice guide onto ice mold, watch rotation bar while inserting into motor.(it only splines one way.) when each piece is lined up, simply push together and reinstall two screws. snap circuit board cover into place. reinstall ice maker into freezer in reverse order.
Was this instruction helpful to you?
Thank you for voting!
burned out Evaporator Fan Motor
simply removed wires from the old motor and gently lifted it out by by the metal clips - put the old bracket on the new motor, snapped on the new fan, replaced the wires, reinstalled the shield. All done in about 15 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kearney from Port Allen, LA
- Parts Used:
- 2198597
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice maker quit making ice.
Ice Maker quit working. Seemed like a water supply issue but when I read the other reviews, I decided to install and see. bolted the bracket on with three screws, slid in place. Nothing happened and about 10 minutes later, I heard the water release to the ise maker and have been making ice ever since.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Owings, MD
- Parts Used:
- WPW10321304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Not enough door storage
Excellent fit and installation. The door bins slid right in and created the extra space needed on the shelves.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Spring, TX
- Parts Used:
- 8201515
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Old motor was not resetting back to proper position halting ice production.
Removed the three motor screws pulled off old motor put new motor in place replaced screws and re-installed. It was producing ice three hours later. I originally tried to obtian these parts directly from Whirlpool in which twice they shipped me the wrong parts. Finally gave up on them and entered the whilrpool part number which crossreferenced to new part number which was correct the first try. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leandro from Baldwin Park, CA
- Parts Used:
- 4389144
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The freezer wouldn't freeze and the refrigerator wouldn't refrigerate.
Same as everybody else on this post. Real easy. Actually, I just wish I would have done it sooner.
Was this instruction helpful to you?
Thank you for voting!