10651799413 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Paul from NAYLOR, MO
- Parts Used:
- WP2188664
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Crack in vegetable drawer
Emptied draw of contents pulled draw out and inserted new drawer....easy pea-zee
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LUC from PALM DESERT, CA
- Parts Used:
- EDR1RXD1
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
light in refrigerator went OFF when in installed the new water filter
STRANGE ! to moment I installed the filter ALL the internal lights in my refrigerator went OFF and never came back.
Strange !! refrigerator works fine but no more light in it !!
My email is : Lucfontaine91@yahoo.com
DON'T USE earthlink email anymore
Strange !! refrigerator works fine but no more light in it !!
My email is : Lucfontaine91@yahoo.com
DON'T USE earthlink email anymore
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from North Port, FL
- Parts Used:
- WP2188664
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken drawer
replaced
Was this instruction helpful to you?
Thank you for voting!
Icemaker Wouldn't Work
I removed the screws that attached the drum housing to the bin. I detached the auger & removed the broken drum assembly, turning the auger to the right, opposite what I thought it should be. I slipped the end of the auger into the new bin coupler & put it in place at the rear of the bin. Next I slipped the auger drum into place & tightened it to the left with a socket wrench. I screwed the drum housing to the bin, put the bin back into the freezer & I now have ice through the door again. Easy repair even for me, a 60+ woman.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from CAMBRIDGE, MN
- Parts Used:
- WPW10515057
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
freezer light out...Fridge light dim
Previously replaced the Fridge light (control board).. The Fridge and Freezer lights were flickering rapidly...LIghts worked fine for four months...then the freezer light went out completely and the fridge light went dim. I unplugged the freezer light and all lights went out! Hooked it back up and ordered new freezer light. After replacing freezer light all three lights work perfectly at full intensity problem solved...For now!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andre from GRAND RAPIDS, MI
- Parts Used:
- EDR1RXD1
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Reset rater filter
Hold both water filter reset touch sensors down together. This will reset the water sensor indicator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carlos from CHICAGO, IL
- Parts Used:
- WPW10515058
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
flashing lights
using a flat blade tool removed old main light board and installed new light board, light now works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darryl from JACKSONVILLE, FL
- Parts Used:
- WPW10515058
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lights Flashing / Strobes
easy peezy - removed old light/module and installed new one works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Monica from EDMOND, OK
- Parts Used:
- W10823511
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
water leaked when the paddel was pushed
Followed the video on parts page. I was worried I would brake the cover but learned from the video the right way to remove the front plate. I found the video very informing. Thank you for saving me a service call and the part cost was minimal compared to a new refrigerator .
Was this instruction helpful to you?
Thank you for voting!
Crisper tray and rack cracked
Removed two set screws from door handle as there was not enough room for the door to open fully. Once that was done, the rack and crisper went in easily. Also needed to install support on right side as that was never installed in the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- J from BOSTON, MA
- Parts Used:
- WPW10276341
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Plastic side-rail cracked. Shelf could no longer support weight on top or in the drawer beneath.
(1) Remove the drawer by pulling it open until it catches. Push up gently on the bottom-rear of the drawer to lift it over the stop tabs in the drawer rail, and pull the drawer out completely. Note: You will need to push the refrigerator door gently to the fully open position to remove the drawer all the way. The door will open about 30 degrees further than where it comes to rest on its own when opened.
(2) Remove the shelf by lifting gently on the front and sliding it forward. Once the rear corners of the shelf are beyond the upper lip of the shelf rail, you can lift the shelf out of the rail, and turn it vertical to remove through the fridge door. Note: the glass in the shelf is meant to stay in, but if its old or damaged it may tip out when you turn the shelf on its side. So you may want to tape it in place before removing the shelf.
(3) Install the new shelf by repeating step 2 in reverse.
(4) Reinstall the drawer by repeating step 1 in reverse.
(2) Remove the shelf by lifting gently on the front and sliding it forward. Once the rear corners of the shelf are beyond the upper lip of the shelf rail, you can lift the shelf out of the rail, and turn it vertical to remove through the fridge door. Note: the glass in the shelf is meant to stay in, but if its old or damaged it may tip out when you turn the shelf on its side. So you may want to tape it in place before removing the shelf.
(3) Install the new shelf by repeating step 2 in reverse.
(4) Reinstall the drawer by repeating step 1 in reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hans from OGDEN, UT
- Parts Used:
- WPW10475495
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Raise side of fridge and slide 2x4 under side with broken wheel.
Remove back side cardboard access cover. About 6 dcrews need to be removed. Remove 9/16” bolt and lower compressor tray frame down to slide out wheel axel. Place wheel in slot and replace axel. Lift compressor tray and replace 9/16” bolt. Replace cardboard cover. Remove 2x4.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from ONEIDA, NY
- Parts Used:
- EDR1RXD1
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Filter indicator light red
Found the filter door in toe kick under freezer door. Opening the door ejected the old filter. Direction indicator arrows were found on inside of filter door, rotation of filter to match arrows important. Pushed new filter in to stop, closing door completed insertion of new filter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darlene from Glasgow, KY
- Parts Used:
- W10852691
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
the floating baffle broke
took the auger off and baffle replaced the baffle put every thing back together installed back to the freezer tried it out it dont work have to tear into the the motor which works the auger to see if anything else is broke.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Jacksonville, FL
- Parts Used:
- 4388736
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Ice would not dispense from the door
Removed ice bucket and discovered the auger drum was broken.
After I received the new part, I removed the front screws of the ice bucket, removed the clip that held the auger and other parts together, and then slide each part off the auger until I got to the broken drum.
Assembly was in reverse except you must pay attention where all the spacers and ice crusher bars go back into the original position. This was the most difficult step.
Works great now, crushed and cubed ice dispenses thru the door like new.
After I received the new part, I removed the front screws of the ice bucket, removed the clip that held the auger and other parts together, and then slide each part off the auger until I got to the broken drum.
Assembly was in reverse except you must pay attention where all the spacers and ice crusher bars go back into the original position. This was the most difficult step.
Works great now, crushed and cubed ice dispenses thru the door like new.
Was this instruction helpful to you?
Thank you for voting!