10651103111 Kenmore Refrigerator - Instructions

Review the video on parts select. Do this first!

The actual repair took less than 30 minutes, including pulling out the refrigerator, performing the repair, and replacing the refrigerator.

Remove the screws holding the cardboard backing to the bottom rear of the refrigerator. Remove the screws holding the pump in place. Remove the electrical connectors and the water hoses from the pump. I needed the wrench to disconnect and reconnect the main inlet hose. Hook everything back up (the sizes of hoses and connectors are different). Replace the cardboard backing. Done!!

I would use Parts Direct again.

I removed the glides under the edges of the meat pan, remove the old pan, put the new pan in and replaced the glides. I was very pleased with PartSelect. I ordered my part, and it arrived the very next day. I will definitely order my next replacement part thru PartSelect.

Be advised that to do this job, you have to take the ice tray and feeder assembly completely apart. The only tricky part is that the nut, part 31 in the drawing, that holds everything together is reverse threaded. Since it's plastic, you're afraid you'll break it. If you know it's reverse threaded to begin with you can go ahead and apply the required force to get it off.

Turn off water supply too ice maker and unplug the fridge power. using a nut driver remove one bottom screw from the bottom, near the front. The other two from the side atop the ice mold. (loosen screws and ice maker will lift up and off.)
I set the ice maker on the counter, snapped of the front cover by hand. using a phillips driver, remove two screws near the bottom corners.(they go through the circuit board into the ice mold)
circuit board in one hand, other end of ice mold in the other, slowly pull apart about 1 inch. remove the silver colored "on, off" bar at the end by snapping the retainer out of the ice mold. (the silver bar stays with the circuit board end)
Watch how the ice guide(white fingers stationary on side of ice mold) hooks too the ice mold on each end. swap ice guide to new ice mold, insert three guide pins on end into holes on the circuit board, while holding ice guide onto ice mold, watch rotation bar while inserting into motor.(it only splines one way.) when each piece is lined up, simply push together and reinstall two screws. snap circuit board cover into place. reinstall ice maker into freezer in reverse order.

I removed 4 screws holding the motor mounting bracket and removed the assy from the unit. I then removed 3 screws holding the motor to the bracket. I put the fan blade on the new motor and reattached the motor to the bracket. I plugged in the wiring adapter to the motor and reinstalled the bracket in the unit with the 4 screws. Finally I attached the unit wiring connector to the motor.
It was relatively easy.

Removed the three motor screws pulled off old motor put new motor in place replaced screws and re-installed. It was producing ice three hours later. I originally tried to obtian these parts directly from Whirlpool in which twice they shipped me the wrong parts. Finally gave up on them and entered the whilrpool part number which crossreferenced to new part number which was correct the first try. Thank you!

Excellent fit and installation. The door bins slid right in and created the extra space needed on the shelves.

simply removed wires from the old motor and gently lifted it out by by the metal clips - put the old bracket on the new motor, snapped on the new fan, replaced the wires, reinstalled the shield. All done in about 15 min.

That was due to the evaporator blocked by the ice. Check found the defrost timer is okay. The next thing I can think of is to replace the Electronic Control Board which is installed in the fridge side top compartment. Ply open the face cover, remove the nut and screw that secure the EC Board. Pull out the cable, mount the new card and re-connect. So simple. It is back in order.

This company is WONDERFUL! I ordered the wrong drawer the first time, but their return process was a snap and the correct drawer arrived the next day. It's great to know that there is someone out there with just about every part you'll need for about any appliance that is truly customer friendly.

After diagnosing two problems (Hot door jambs between the fridge and freezer, as well as excessive leaking in the freezer) I ordered the parts online. I received a new condenser fan kit and a new water inlet valve. Both were easy to replace. The hardest part was getting the old condenser fan out of the fridge, but I took off the fan blade first, and pulled that out, then I was able to get the fan motor out. The water inlet valve was pretty easy as well, just make sure that you shut the water off completely. I made the mistake of only turning it a quarter turn at the valve on the wall when I should have made a half turn on the valve. Slight water mess in the kitchen, but if that's the worst thing that happened on this repair, then I'm OK with that. Both were easy to replace and the cost saved of not having to call a repairman was the extra added bonus.

Watched the website repair & adjustment video, ordered the part which was exactly like the one currently in the fridge. Took only 10 min. to install. Then, 2 hours later we had ice! And still have ice on a consitent basis. Easy fix, life's good!

Same as everybody else on this post. Real easy. Actually, I just wish I would have done it sooner.

Removed front plastic grill and screws holding the filter in place. Also removed lower back cardboard panel to access water lines. Video on this website told me how to remove water lines from filter, you must depress a collar around the water line while pulling out the water line. Then install the new Water Filter Housing and water lines. The only problems I had was the tight space to work in and one of the water lines was leaking, but pushing the water line in further solved the problem.

First I unplugged the unit, then I popped off the cover to the icemaker electronics. Removed 4 screws, pulled out the broken electronic panel, and replaced with the new one. Returned the screws and cover. The next moring the ice bin was full.

This must have saved me $300, and the inconvernience of waiting around for the repair man. He would have made two trips since he would never have had this part with him.