10651103111 Kenmore Refrigerator - Instructions

Cleaning out the freezer took the longest time. Once the freezer was clean I turned off the freezer which did not deactivate the light in the freezer. This is a tight area to work in and not having to hold a flashlight made the job much easier. I then removed the shelf slider brackets for the 3 lower pullout drawers. The next step was to remove the interior aluminum back panel (6 screws) which covers the evaporator motor and the coil. Before removing the 3 electric wires that are attached to the evaporator motor make sure the power is off to the motor. The removal of the motor was fairly straightforward and I would suggest removing the plastic fan blade first and then the connector wires. It helped knowing in advance that the plastic fan blade would come off with a little prying. Be careful when prying the fan off so that you don’t damage the plastic motor mount bracket. Once you have installed the motor I would suggest turning the freezer back on to make sure that the evaporator motor works before reinstalling the aluminum back panel and slider brackets.

The ice maker was not getting water. I hotwired the water valve by switching the connectors for the water dispenser and ice maker water valves and water flowed into the icemaker when the water dispenser lever was pushed. I wronly assumed the water valve was good. I removed the icemaker and determined that the gear motor was not getting power in the position the icemaker had stopped.In this position, the thermostat determines when the motor gets power so I replaced the thermostat. The icemaker still would not get water! As it turns out, the water solenoid was sticking due to a deteriorated rubber washer which let the solenoid plunger get too far out of the magnetic field. I replaced the water solenoid assy and all is well. Don't get fooled by hotwiring the valve. If it isn't getting water, the solenoid probably is the culprit.

open ice maker door, use mirror to view slot in front of ice maker, slip piece in place and done

The procedure was straightforward. I removed the cardboard backing on the lower back of the refrigerator to expose the fan unit. I then undid the electrical harness at the fan. I then removed the three screws securing the fan motor to the metal bracket. This is the hardest part in that I had to reach through and get to the screws with my small tools. I then removed the old motor and blades and placed the new motor and blades. Again, a bit tricky trying to get the three screws mounted into the bracket...small tools and hands helps. After that I used the electrical harness supplied with the kit to plug into the new motor and I was done.

Replaced the door cam on bottom of fridge door. ONE THING TO UNDERSTAND- THERE ARE 2 CAMS ON THE DOOR, LOWER AND UPPER, BUT THE UPPER CAM IS NOT LISTED ON THE "DOOR HARDWARE" DRAWING, ITS LISTED ON THE MAIN BODY DRAWING! BE SURE TO GET BOTH CAMS! (PARTSELECT COULD MAKE A NOTE THAT WHEN PEOPLE LOOK UP LOWER CAM, PUT A NOTE IN THERE SAYING Y0U NEED UPPER TOO!)So I had to order the upper cam later and install later. BUT it is quite easy to replace, unlike the video, I only needed 1 tool! The nut driver (electric screwdriver w nut driver head). Thanks -RF

I took the old drawer out and replaced it with the new one!
I hooked a new door bin in the door for more room!

DISCONNECT POWER. Removed all shelves/baskets.Popped upper panel off (just clips in) Removed 6 screws in lower back panel ( 3 each side) slid panel in place but down. You can then easily see the defrost thermostat/defrost termination switch. Cut the wire connectors (pink n brown wire) stripped back wire, attached new defrost thermostat. Thermostat clips on. New thermostat ohm's at 5.5, old one was "open". Slid cover back up meeting the upper cover grooves. Screwed lower panel in. Put shelves etc back in. Plugged in. Turns on, put a bottle of water in freezer. Checked a while later, frozen. has been frozen for a week.
-James

I have a side by side so in order to access the bi-metal switch I first had to empty out the freezer. The switch is clipped on to the top of the evaporator coil. I had to remove 8 screws to remove the back panel of the freezer compartment. The bi-metal switch was right there in plain view. There are two colored wires that come out of the switch. I tried pulling them out of the socket they were plugged into but gave up for fear of breaking something. I ended up cutting the wires and splicing them together. I used the plastic twist caps. I made sure when I closed everything back up that the open end of the caps were pointing down so no water can accumulate in them. It has been 3 days now and so far so good

Parts arrived at 2:30PM.

Read instructions, gathered tools, and went to work. I'd already watched an online video at your site on how to do the repair.

Removed the hinge cover covering the hinge top by using a nut driver to remove the single screw holding it in place. (The video described an older frige and it did not have a screw. I figured that out when I finally went and got a ladder. I had tried to pop it out like the video shows.) There are three screws holding the hinge top in place. I tried using the nut driver to remove the screws but they were pretty firmly in place. I resorted to using my ratchet wrench and that made it easy. (Keep track of your screws, one of mine rolled under a cereal box on top of the frige and I thought I would never find it.)

I had emptied out all the items on the door of the frige, removing the shelves. It was easy to lift the door off of the bottom hinge and lay it on its side against the ladder. At this point I had my son hold the door steady (its kind of unwieldy and 'slippery' when you are trying to remove a screw from the bottom of the door.)

I removed the screw that held the plastic Door Closer, Upper Cam using the nut driver. I used a straight bladed screw driver to pry the old part out of the door (it has an insert for the hinge pin and it had been in place a long time). I also cleaned off the bottom of the frige door (you would be surprised what gets stuck on there - obviously someone spilled oranged juice on the floor and it splashed up on the bottom of the door). The old part had a lot of particle dust that came off it when I removed it. The new part popped right into place and I screwed it back in. The video shows that the repairman had to use a drill and tap set to rethread a larger hole but I just put the old screw back and it held fine. The video also showed the repairman adjusting the Door Stop Bracket but I didn't have to do that, the new cam installation wasn't impeded by the bracket.

I moved to the frige cabinet (again, good to have a second pair of hands to keep track of the door and not let it get damaged while I turned my attention to the Door Closer, Lower Cam. I used the nut driver to remove the screw holdin it to the hinge bottom. It came off easily (it practically fell apart and turned to dust). I placed the new cam and screwed it in using the old screw. No problem.

You could put the door back on with one person but it helps to have two. One to manhandle the door and the other to place it on the lower hinge post.

I put the upper hinge back on and put in the three screws but I left them lose so that I could adjust the door. When I tighted the single screw closest to the door after positioning the door, we tested how it opened and it was hitting the side of the interior cabinet when it closed - you could feel it dragging and it made a clunk/swoosh sound. We readjusted the door using the outside upper corner as a guide and retightened the screw. This time there was no problem. We tighted the other two screws using the ratchet wrench and then put the plastic hinge cover back on with the single screw using the nut driver.

Took us about 25 minutes and made my wife very happy (biggest benefit). The door now 'locks' open and 'locks' closed just like when we bought it and the two doors are aligned (level accross the top) which should have been a dead giveaway that the door closing cams had worn down.

Done by 3:00PM.

After removing the old icemaker ( 3 screws) I put the new piece right back in place . Just plugged in the wiring that was already in place from the old icemaker, Hung the new ice maker on the two screws left in the wall of the freezer. Be sure and put the arm on the new icemaker prior to hanging it on the wall. tighten the screws and put the white plastic end cap over the exposed rotor end. Turn on the water to the refridgerator and in about two hours you will have ice. Be sure and turn off the water to fridge before undoing the old icemaker and unplug the fridge from elctric outlet during the whole process. Simple

I removed the screw holding the spring steel retainer/clip using a quarter inch ratchet wrench a swivel with a quarter inch socket and a short extention, then just installed the new one. This spring steal through the door ice maker / water despenser lever spring was an easy fix.
I found you by googling appliance repair parts, and found your site really easy to use. I couldn't believe how fast the part came and the very reasonable price. I put you on my web browser's favorites.
Thanks,
Ron

due to over filling and closing the drawers with the door and kicking, the plastic runners broke. Also, over filling the drawers did not help.
AS for the repair, the only difficulty was getting the right drawer in the right spot. Since I replaced both the veggie and meat drawer at the same time, I got them confused. On drawer is longer than the other. other than that, no problem.

First removed the outside cover plate which was some what scary not to break plastic cover. Had read about another discription of removal of cover to start from the bottom because the top is inserted in slots that would have broken if removed from the top. After cover plate removed it was simple to remove the broken parts and install the new parts. The most difficult part to put back in was the spring and rod had to be inserted the same time.

Remove the knobs and faceplate to get at the screws behind it. Removing the sensor is a bit involved but everything else is fairly straight forward. See other postings for description / order of operation. Replacement took less than 30 minutes.
Works great now!

Found the control bracket housing had broken and micro switch for the water pump was not making contact with mechanical link. (In other words when you put a cup under the dispenser and push water did NOT come out.)

I removed the faceplate and switches, removed all the switches and installed them in the new control bracket. Installed new control bracket into fridge and tested. Works! Reinstalled faceplate and switches and drained system for a few minutes. Man I forgot how good filtered water tasted!