25370412413 Kenmore Refrigerator - Instructions

Turned off water supply disconnected hose from valve removed cardboard backing removed the screws holding valve ass'y disconnected the three wire connections disconnected five hoses then cut and installed in new valve per instructions provided reconnected three wires reinstalled valve ass'y turned water supply back on and checked for leaks by engageing filtered drinking water in the refrigerator door replaced backing to complete job.

remove back cardboard panel, cut off water supply, remove screws holding valve to back of refrigerator, unscrew water lines & reattach to same fittings on new valve, screw new valve in place, replace cardboard cover.

Installed new valve.There are several pieces of tubing coming off of the valve. Pay close attention to where they go. Color coordination is poor on the new valve.

Removed old water pump and cut off ends of all lines. Plugged them into each water inlet/outlet and turned it on. Instant water to dispenser but took about 6 hours for ice maker to get water. Had to prime the ice maker. Works great and saved a lot of money ordering parts from you. Thanks.

1. Turn off water in line to refrigerator. 2. disconnect hose from refrigerator. 3. Remove back cardboard panel at bottom of refrigerator. 4 Remove 2 screws holding in the valve assembly at bottom right. 5. best way I found to remove hoses (all color coded) is to cut with razor knife at the white collar. cut clean and square. 6. disconnect electrical (also color coded) 7. connect hoses to valve assembly by pushing hose firmly into hole. If you are familiar with PEX then this is the same. Reconnect electrical. Reconnect to refrigerator... 3,2,1 your done. It will take a couple cycles to get the air out of the lines.

Followed the instructions from another person in the Part Select water valve section and from the video on the same page. Excellent instructions and very easy installation. Water dispenser and ice maker began performing properly as soon as the refrigerator was plugged back in to the power.

Purchased a replacement part only to find the new part had push on fitting and my part has screw on fittings. Went to Youtube where Partselect had a video on how to replace the part from screw fittings to push on fittings

I turned off the water, removed the cardboard cover from the back of the refrigerator; removed the 2 screws holding the water valve in place; unscrewed the plastic tubing from the valve; unplugged the wires to each solenoid (3); the old valve had threaded connections for the plastic water lines, the new valve didn't; I had to cut the ferrel off of the plastic lines so I could insert them into the new valve and then press the connector into the valve (I didn't anticipate something like this, but it worked fine); I reconnected the wiring and screwed the valve back into place. The ice maker started making ice and the water stopped dripping from the dispenser. The best $65 I've ever spent.

The water flow on or refrigerator was just trickling out. After trying to make sure there was no kink in hose, I called for replacement. Water flows great now... actually better than when new.

I changed the valve but still no ice, changed the filter also. think it was just froze. could have saved me 70 bucks

Easy to assemble after cutting original water line fittings off. Use sharp knife to keep from damaging end of water lines.

removed backing to refrig unscrewed 2 screws from bracket pulled unit out unhooked hoses and elec plug's / putting in new just reversed the instalation

My part had threaded fittings. The part that I received had snap fittings. Once I realized that that snap fittings worked with the bare tubing and not any special tip endings, I simply cut off the ends of my tubing that mated with the threaded fittings. I then had bare tubing that snapped into the snap fittings. Two minutes later, the part was in place and the job was done. Problem solved.

problem still persists part did not fix problem. made repairs recommended per your site.

Turned off the water supply ,pulled the plug removed two screws to access theater lines the new valve body was a little different than the original I had to cut off the end of each hose and push them in to the new connections the hoses are size and color coded replaced the two screws put the water line on plugged it in and turned on the water checked for leaks twice and replaced the back cover