2537041341A Kenmore Refrigerator - Instructions

Watched the video and read some comments and from that it was easy

Removed lower cardboard cover, shut off water supply valve, unpluged frig. Used wrench to remove 3/8 water line from water valve, removed electrical connectors from solenoids, used fingers to unscrew water connections from valve.

i only ordered 1, so i replaced each 1 then moved to the next. still no light, so it must be someting else. will try to check the wires with a volt meter to see if i have power next. something wierd happen, when i accidently touch the back of the led board, it lit up, small but still light up. hoping that means the led board is goo, must be in the wiring. i saw it had a main led board so will check the power to that.

Water was leaking so I replaced the entire valve and just followed the color codes and thats it. Plug and play.

took the back off refridgerator, disconnected water valve assembly, then disconnected water lines and electrcal connectors. also i received the part in less than 24 hours

I had a repair man do the work.
That's always best.There was one day delivery on the part and the price was great. Thanks

turned off water supply, removed cardboard back, removed supply line, unhooked all color coded connections,took out bad water valve and replaced with new one note: the new valve came with pex connections so i carefully cut off flared tubing ends with sharp razor knife making sure when i pushed tubing into new valve that i did so with some force until i HEARD and felt them snap in place very simple plus i received the new valve in 2 days very happy with PartsSelect.com you CAN do it

Turned off water supply disconnected hose from valve removed cardboard backing removed the screws holding valve ass'y disconnected the three wire connections disconnected five hoses then cut and installed in new valve per instructions provided reconnected three wires reinstalled valve ass'y turned water supply back on and checked for leaks by engageing filtered drinking water in the refrigerator door replaced backing to complete job.

remove back cardboard panel, cut off water supply, remove screws holding valve to back of refrigerator, unscrew water lines & reattach to same fittings on new valve, screw new valve in place, replace cardboard cover.

Turned off the water supply ,pulled the plug removed two screws to access theater lines the new valve body was a little different than the original I had to cut off the end of each hose and push them in to the new connections the hoses are size and color coded replaced the two screws put the water line on plugged it in and turned on the water checked for leaks twice and replaced the back cover

Purchased a replacement part only to find the new part had push on fitting and my part has screw on fittings. Went to Youtube where Partselect had a video on how to replace the part from screw fittings to push on fittings

I turned off the water, removed the cardboard cover from the back of the refrigerator; removed the 2 screws holding the water valve in place; unscrewed the plastic tubing from the valve; unplugged the wires to each solenoid (3); the old valve had threaded connections for the plastic water lines, the new valve didn't; I had to cut the ferrel off of the plastic lines so I could insert them into the new valve and then press the connector into the valve (I didn't anticipate something like this, but it worked fine); I reconnected the wiring and screwed the valve back into place. The ice maker started making ice and the water stopped dripping from the dispenser. The best $65 I've ever spent.

If this happens to you the first thing I would do is shut off the freezer and, using a hair dryer, melt the ice in the ice maker and heat up the water inlet to make sure it is not froze up. Turn the freezer back on and wait to see if that cures the problem. If not, order the new water inlet valve and follow the simple instructions in the video provided on the PartSelect website. I have never have a more pleasant experience with any parts/repair service than I did with PartSelect. After ordering that part it came within the time they stated and their help with the install was great. Also helpful were the other customers talking about their problems and solutions.Thanks to PartSelect I now have Ice and a happy wife. Happy wife--happy life.

The new inlet valve came with pisco connectors so had to cut the end of the tubes off. Before doing this I marked all the tubes to make sure they were replaced in the correct order. The pisco connectors are great to use and very quick. The total install time was about 20 to 30 minutes. While you have the back of the frig off make sure you vaccuum the fan and coils. It was making ice in less than 20 minutes.

First I watched the PartSelect installation video. Then unplugged the power and shut off the water valve on the wall. I used a 1/4" nut driver and removed (4) screws on the back bottom cover of the refrigerator and removed the cover. I removed the (2) mounting screws on the back lower right side of the refrigerator and removed the triple water valve assembly. I then marked the (4) water lines and (3) solenoid connectors with numbers, to make sure they get connected back in the same place, and then I removed them. I used a retractable blade knife to cut the ends of the water lines perpendicular. I pushed the (4) water lines into the valve holes and plugged the solenoid connectors back onto the new triple valve assembly. I mounted the new triple valve, put the back cover on, turned on the water, checked for water leaks. There were no leaks.Then I plugged in the power and waited for it to fill up the ice tray. It works perfectly now ! And it was really easy ! Thank You PartSelect for making this repair easy for me.