25370419419 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert A. from St. Augustine, FL
- Parts Used:
- 242252702
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Ice maker wouldn't fill
I had a repair man do the work.
That's always best.There was one day delivery on the part and the price was great. Thanks
That's always best.There was one day delivery on the part and the price was great. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mark from east greenwich, RI
- Parts Used:
- 242252702
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
not making ice
turned off water supply, removed cardboard back, removed supply line, unhooked all color coded connections,took out bad water valve and replaced with new one note: the new valve came with pex connections so i carefully cut off flared tubing ends with sharp razor knife making sure when i pushed tubing into new valve that i did so with some force until i HEARD and felt them snap in place very simple plus i received the new valve in 2 days very happy with PartsSelect.com you CAN do it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jamie from Weeki Wachee, FL
- Parts Used:
- 242252702
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set, Wrench (Adjustable)
Water leaking from broken intake water line
Turned off water supply disconnected hose from valve removed cardboard backing removed the screws holding valve ass'y disconnected the three wire connections disconnected five hoses then cut and installed in new valve per instructions provided reconnected three wires reinstalled valve ass'y turned water supply back on and checked for leaks by engageing filtered drinking water in the refrigerator door replaced backing to complete job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mike from tampa, FL
- Parts Used:
- 242252702
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
water spraying from behind refrigerator
remove back cardboard panel, cut off water supply, remove screws holding valve to back of refrigerator, unscrew water lines & reattach to same fittings on new valve, screw new valve in place, replace cardboard cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Indiana, PA
- Parts Used:
- 242252702
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
water valve leaking
Installed new valve.There are several pieces of tubing coming off of the valve. Pay close attention to where they go. Color coordination is poor on the new valve.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from White Springs, FL
- Parts Used:
- 242252702
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
water dispenser/ice maker inop
Removed old water pump and cut off ends of all lines. Plugged them into each water inlet/outlet and turned it on. Instant water to dispenser but took about 6 hours for ice maker to get water. Had to prime the ice maker. Works great and saved a lot of money ordering parts from you. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Levern from Mc Donald, TN
- Parts Used:
- 242252702
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
no water flowed to the ice maker
1. Turn off water in line to refrigerator. 2. disconnect hose from refrigerator. 3. Remove back cardboard panel at bottom of refrigerator. 4 Remove 2 screws holding in the valve assembly at bottom right. 5. best way I found to remove hoses (all color coded) is to cut with razor knife at the white collar. cut clean and square. 6. disconnect electrical (also color coded) 7. connect hoses to valve assembly by pushing hose firmly into hole. If you are familiar with PEX then this is the same. Reconnect electrical. Reconnect to refrigerator... 3,2,1 your done. It will take a couple cycles to get the air out of the lines.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Cuba, NM
- Parts Used:
- 242252702
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Ice Maker Not Getting Water
Followed the instructions from another person in the Part Select water valve section and from the video on the same page. Excellent instructions and very easy installation. Water dispenser and ice maker began performing properly as soon as the refrigerator was plugged back in to the power.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Brant Lake, NY
- Parts Used:
- 242252702
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Slow Flow of Water
The water flow on or refrigerator was just trickling out. After trying to make sure there was no kink in hose, I called for replacement. Water flows great now... actually better than when new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glen from Black River Falls, WI
- Parts Used:
- 242252702
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
No Ice
I changed the valve but still no ice, changed the filter also. think it was just froze. could have saved me 70 bucks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Wilmington, NC
- Parts Used:
- 242252702
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
water valve leak
Easy to assemble after cutting original water line fittings off. Use sharp knife to keep from damaging end of water lines.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kevin from east haven, CT
- Parts Used:
- 242252702
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
ice maker inlet leaking
removed backing to refrig unscrewed 2 screws from bracket pulled unit out unhooked hoses and elec plug's / putting in new just reversed the instalation
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Omar from Vestal, NY
- Parts Used:
- 242252702
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Leaking water
My part had threaded fittings. The part that I received had snap fittings. Once I realized that that snap fittings worked with the bare tubing and not any special tip endings, I simply cut off the ends of my tubing that mated with the threaded fittings. I then had bare tubing that snapped into the snap fittings. Two minutes later, the part was in place and the job was done. Problem solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bobby from Butner, NC
- Parts Used:
- 242252702
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
ice maker not making ice
problem still persists part did not fix problem. made repairs recommended per your site.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ray from Westland, MI
- Parts Used:
- 242252702
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
leak at one of the valves in the back of refrigerator
Turned off the water supply ,pulled the plug removed two screws to access theater lines the new valve body was a little different than the original I had to cut off the end of each hose and push them in to the new connections the hoses are size and color coded replaced the two screws put the water line on plugged it in and turned on the water checked for leaks twice and replaced the back cover
Was this instruction helpful to you?
Thank you for voting!