25370633411 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Willard from Plymouth, MA
- Parts Used:
- 240385201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken draw
Pulled Out Broken Draw then put new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from New Fairfield, CT
- Parts Used:
- 240350608
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Crisper glass shelf shattered during cleaning.
Extremely easy repair for a 76 year old woman. I just followed the very clear video instructions provided with my order and my fridge was as good as new within 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Curtis from HOISINGTON, KS
- Parts Used:
- 241798231
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice Maker not producing / Clicking / Off-cycle
We love our ice here. I seem to replace the ice makers one to two times a year. Generally the ice cycle gets off for some reason and it starts making loud popping/clicking noises (gear grinding). Its easy to replace. Simply loosen two screws holding the unit to inside of freezer and disconnecting the wiring harness. Unit slide up and out. Replacement is super easy (5 mins or less). Bam! Ice!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from BRIMFIELD, MA
- Parts Used:
- 242193218
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Seal kept pulling causing sweating on freezer door which caused water to be on floor
On this model I just pulled out old seal by hand. Made sure everything was clean. Then literally grabbed new seal lined up to freezer door, started at one corner and pushed seal in place. It went right in flawlessly. Perfect fit. Literally took less than 5 mins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carey from PORTSMOUTH, VA
- Parts Used:
- 241798231
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Didn't make ice
Unplug refrigerator , loosing two screws. Lift ice maker up to remove from position. Disconnect electrical connection. Reverse procedure to install new ice maker.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from PANAMA CITY, FL
- Parts Used:
- 241798231
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice maker broke again!
This refrigerator is less than 2 years old. I have had to replace the ice maker 2 times now. Cheap ass parts! Only one ice maker you can order so just be prepared to replace it yearly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from ELKHART LAKE, WI
- Parts Used:
- 242218602
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The original plastic deli drawer frame part broke.
1) Remove deli drawer from the deli cover frame by pulling straight out.
2) Carefully remove broken deli cover frame and glass shelf from the refrigerator. The glass shelf just lays in the frame.
3) Separate the glass shelf from broken frame. No tools required.
4) Carefully wash glass shelf and set aside.
5) Install new deli cover frame at your favorite shelf height.
6) Carefully install glass shelf. Note that the glass shelf fits under a lip in the deli cover frame at the front.
7) Install deli drawer.
2) Carefully remove broken deli cover frame and glass shelf from the refrigerator. The glass shelf just lays in the frame.
3) Separate the glass shelf from broken frame. No tools required.
4) Carefully wash glass shelf and set aside.
5) Install new deli cover frame at your favorite shelf height.
6) Carefully install glass shelf. Note that the glass shelf fits under a lip in the deli cover frame at the front.
7) Install deli drawer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from SHERIDAN, IL
- Parts Used:
- 242252603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Water Inlet Valve not sutting off
very easy, 1 screw, 2 tube connectors, hardest part was pulling refer. out of enclosure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tommie from Port Lavaca, TX
- Parts Used:
- 241798231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
The ice maker quit producing ie
Purchased a new ice maker assembly and installed. Very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from CORP CHRISTI, TX
- Parts Used:
- 241798231
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
ICE MAKER NOT MAKING ICE.
LOOSENED THE TWO SMALL SCREWS THAT HOLD THE ICE MAKER UP INSIDE THE FREEZER. DISCONNECTED THE WIRING HARNESS. TOOK THE OLD ICE MAKER OUT AND JUST INSTALLED THE NEW ONE IN REVERSE ORDER. LATER THAT DAY I HAD FRESH ICE FOR THE FIRST TIME IN WEEKS!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from HOUSTON, TX
- Parts Used:
- 242252603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Ice maker not making ice
Pulled unit away from wall and shut off water and unplugged unit. Installed water valve and reassembled, plugged back in and turned on water and checked for leaks. All good. However there is no water getting into the ice maker. The unit itself is going thru a cycle of attempting to make ice and the bail is moving and you can hear the solenoid activate but no water. I have tried to blow thru the tube going to the maker but it seems to be plugged by something. I do not know if there is another valve up there or how to clean it out. Any help would be greatly appreciated.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Billy from CHATSWORTH, GA
- Parts Used:
- 241798231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
the gear was stripped on the old ice maker and had to be replaced
was very easy. just ordered a new ice maker which was delivered in a few days. The installation was so simple. Just plugged the new ice maker in and hung the unit on the 2 screws. And then tightened the screws with a 1/4 in nut driver.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from henrico, VA
- Parts Used:
- 241639502
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Socket set
The new motor mount screw holes were not threaded.
I had to tap the screw holes with a 8/32 tap so that the screws would not bind.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Glen Allen, VA
- Parts Used:
- 242252603
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers
ice maker will not make ice
Installed new fill valve in less than 30 minutes and waited for 24-8 hours for results to no avail. Ice maker mechanism was shot and still would not work. Went to Lowes and bought entire ice maker add on kit for my model ice box and installed in 30 minutes and have been making ice ever since. Your 99% cure rate was 100% incorrect. Save the time and effort and go to a big box store and just get a new ice maker. By the way, it only costs about $20 more to do that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from Stow, OH
- Parts Used:
- 241796405
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Ice Maker not getting any water
1). Shut off water supply to fridge. 2). Move fridge out to gain access to back of fridge. 3). Remove poly line to water tube have a glass handy to catch any remaining water that might be in line. Some may have a foam insulating washer around water tube remove it first. 4). My Sears-Kenmore was a twist lock water tube have to turn it to left or right depending on brand to remove tube. 5). After removing make sure tube didn't just have water frozen in tube ( that was my problem ) run it under hot water frozen piece will come out. 5). Problem fixed, reverse directions to re-install tube!
Was this instruction helpful to you?
Thank you for voting!