25370629410 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
refer door hinges were lost during the move in to our first home.
The center door hinge was still attached to the refridgerator so I only had to install the bottom and top hinges. I also moved the door handles to the other side so the doors open the "right" way. The hinges were just 2 bolts and 3 screws. Now, just if the repair man from our home warrentee company would show up to fix the refridgerator. It's blowing hot air!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diana from N LAS VEGAS, NV
- Parts Used:
- 240350609
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The glass shelf broke above the 2 drawers on the bottom
Just lay the new glass shelf into the groves. The shelf was too big and would not fit properly down into the groves.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from POTTSTOWN, PA
- Parts Used:
- 241798231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker stopped making ice
loosened 2 screws with 1/4 inch nut driver, disconnected electric connection lifted old ice maker out, replaced it with new one hooked up electric plug tightened 2 screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tommie from Port Lavaca, TX
- Parts Used:
- 241798231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
The ice maker quit producing ie
Purchased a new ice maker assembly and installed. Very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Curtis from HOISINGTON, KS
- Parts Used:
- 241798231
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice Maker not producing / Clicking / Off-cycle
We love our ice here. I seem to replace the ice makers one to two times a year. Generally the ice cycle gets off for some reason and it starts making loud popping/clicking noises (gear grinding). Its easy to replace. Simply loosen two screws holding the unit to inside of freezer and disconnecting the wiring harness. Unit slide up and out. Replacement is super easy (5 mins or less). Bam! Ice!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- henry from alhambra, CA
- Parts Used:
- 241798231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
my ice maker stopped working
removed ice maker storage holder and then remove two philip screws and unplugged four pin connector. removed ice maker and installed new one . very easy to do
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karla from UNION, MO
- Parts Used:
- 241554901
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Socket set
Refrigerator light stopped working
The bulb wasn't the issue so I was hopeful the switch was. utube helped me some, but figuring my model was different than any on utube. Got the switch in and plugged it back in. Moment of truth. Didn't light. Ugggh! Out $50 for switch plus $20 for nut driver set.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from PANAMA CITY, FL
- Parts Used:
- 241798231
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice maker broke again!
This refrigerator is less than 2 years old. I have had to replace the ice maker 2 times now. Cheap ass parts! Only one ice maker you can order so just be prepared to replace it yearly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Willard from Plymouth, MA
- Parts Used:
- 240385201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken draw
Pulled Out Broken Draw then put new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carey from PORTSMOUTH, VA
- Parts Used:
- 241798231
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Didn't make ice
Unplug refrigerator , loosing two screws. Lift ice maker up to remove from position. Disconnect electrical connection. Reverse procedure to install new ice maker.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from SHERIDAN, IL
- Parts Used:
- 242252603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Water Inlet Valve not sutting off
very easy, 1 screw, 2 tube connectors, hardest part was pulling refer. out of enclosure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DONNA from SEMINOLE, FL
- Parts Used:
- 240350609
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Glass Pan Cover
Placed the new glass pan cover. No issues. The part was in original condition and fit perfectly. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from CORP CHRISTI, TX
- Parts Used:
- 241798231
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
ICE MAKER NOT MAKING ICE.
LOOSENED THE TWO SMALL SCREWS THAT HOLD THE ICE MAKER UP INSIDE THE FREEZER. DISCONNECTED THE WIRING HARNESS. TOOK THE OLD ICE MAKER OUT AND JUST INSTALLED THE NEW ONE IN REVERSE ORDER. LATER THAT DAY I HAD FRESH ICE FOR THE FIRST TIME IN WEEKS!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from HOUSTON, TX
- Parts Used:
- 242252603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Ice maker not making ice
Pulled unit away from wall and shut off water and unplugged unit. Installed water valve and reassembled, plugged back in and turned on water and checked for leaks. All good. However there is no water getting into the ice maker. The unit itself is going thru a cycle of attempting to make ice and the bail is moving and you can hear the solenoid activate but no water. I have tried to blow thru the tube going to the maker but it seems to be plugged by something. I do not know if there is another valve up there or how to clean it out. Any help would be greatly appreciated.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Billy from CHATSWORTH, GA
- Parts Used:
- 241798231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
the gear was stripped on the old ice maker and had to be replaced
was very easy. just ordered a new ice maker which was delivered in a few days. The installation was so simple. Just plugged the new ice maker in and hung the unit on the 2 screws. And then tightened the screws with a 1/4 in nut driver.
Was this instruction helpful to you?
Thank you for voting!