25370622410 Kenmore Refrigerator - Instructions

No instructions included, so it took a little bit of staring at the new part to figure out how it works. The barbed ridge on the gasket fits into a slot on the door. The flat face of the gasket has an internal magnetic strip that helps keep the seal tight against the steel face of the refrigerator. Installation requires no tools. This is the basic process:
1) Unbox the new gasket and get it ready to install so you don't have to leave the fridge open too long.
2) Open the door and grab the old gasket at one of the corners and pull away. This will unseat the barbed ridge I mentioned above. Work your way around the door until the whole gasket is free.
3) Set aside the old gasket
4) Grab a moistened paper towel and wipe down the (now exposed) sealing surface of the fridge and door.
5) Align the new gasket in the door and start pushing the barb into place. I found that the new gasket seemed slightly oversize compared to the original, so it took a little tweaking. What worked for me was to get all the corners seated, then work my way around the door making sure the gasket is fully seated.
6) Once you have the new gasket installed, close the door to make sure everything fits OK.
7) Open the door again and run your finger along the inside edge of the gasket seal. What you want to do is fold the edge of the gasket down so it lays flat against the outer wall of the door.
8) Shut the door and look from the sides and top to try to spot any gaps. You should be able to poke the gasket from the side and get the magnet strips to click into place. It seems like after a day or so the gasket 'relaxed' and I didn't have to worry about this anymore.
9) Dispose of the old gasket. I was able to pull the gasket into four pieces (separating at the corners) so it would fit in my city trash can...

Unplugged faulty ice maker, removed two screws holding it to the refrigerator and took it out. Reversed the operation with the new ice maker and after a few minutes presto, we have ice.

I had put in a new ice maker and it still had the problem, (I needed the Ice maker anyway) I installed the vale and while I was at it I put a five year filter on the water line that went from the value to the Ice maker, it took less than one hours, the ice is making like it did when it was new, I could not be more please at theis time. Thanks for your Interest. God bless.

The repair was super easy. There are no retainer screws to deal with. You just pull the old gasket off of the door and press the new gasket on. I used a large flathead screwdriver to help start the removal by prying the first corner out of the groove. Once you get it started, the rest comes out easy. To put the new gasket on, you just firmly press it into the groove on the door.
I've read other instructions that say to soak the new gasket in warm water before installation. I didn't do this. Instead, I just used a hair dryer to heat the gasket once it was on the door. Then I closed the door and ran a finger between the fold in the gasket to make sure there was a good seal between the fridge and the door. Don't open the door for an hour so the gasket will form to the shape of the fridge opening. That's it. It works great now. Problem solved.

Useing 2 fingers pulled old one out from its seat grove in door and started at one corner pressing the new one in groved slot the old one came out from. Auctually took less than 5 minutes

Reviewed the video on your website and followed the directions to the letter. Great video

The repair was very, very easy. The old Gasket was easily removed by pulling at (1) of the (4) corners and simply pull from slot around the full perimeter of the door. No tools of any kind are needed. Replacement of the new Gasket was simply to again start at (1) corner by pushing new gasket into the perimeter slot and using fingers push into the door grove all the way around. This install took no more than 10-15 minutes max.

Loosen two screws, unclip electrical connection, remove ice maker, remove l shaped leveling piece of metal from old one, put on new one. Install in reverse order. Hint.. when loosening two screws, use a mirror

I removed a couple of screws from the old part, and inserted the new part. Replaced the screws and I was done. No problem. I'm an almost 60 year old woman, and fixed this myself. It was so easy.

At first I tried to insall the new gasket with the door still attached to the refrigerator. It was difficult to assure that the bottom of the gasket was properly installed at the bottom. As a result I removed the door from the refrigerator, finished installing the gasket and then put the door back on the refrigerator

Followed the steps in the video on your site, really easy to do.

My 4 year old grandson used the frig door as a swing.The bottom hinge cracked, then the door wouldn't seal. I propped the door up with some books, removed the broken hinge (2 bolts) and replaced with the new part. Simple fix on the door, only time will fix the 4 year old!

I slid the new glass in place

Pulled the refrigerator out from the wall. Then unplugged it took my nutdriver with a1/4" socket on it and took out the screws from the cardboard back on the bottom of the refrigerator. Then I removed the two screws holding the water valve on. Then I unscrewed the supply water line from the main water inlet valve. Then I removed the outlet waterline going to the ice maker from the water valve. Then I reversed the procedure to put it back together. Hooked up the main water line and turned the water valve on for the water to flow to the valve at first nothing happened had to wait for a couple of hours for everything else to get to the right temperature before the ice maker would start making ice.

I removed the back cover and removed the clip holding the compressor- run capacitor and start relay. I replaced these 2 components and clean the dust from the frig., and from the bottom of the floor. I replaced the back cover ; Loss about $300 worth of meat when when the frig. failed. Then I thought that, during these turbulent times, there are many which don't have a refrigerator or any meat to place in it, The refrigerator is "running" normal again.