25370633410 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Edward from Andover, CT
- Parts Used:
- 5304507147
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Refrigerator door was not sealing correctly.
Remove screws from lower hinge and carefully remove the door. In my case it was the lower bearing, flip door upside down being careful to remove anything which might fall off first. I removed the door stop and then pulled the broken bearing out with pliers. Then I pushed the new one in and reassembled it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Benjamin from Jersey City, NJ
- Parts Used:
- 5304507147
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
The refrigerator door did not come for the opening swing to be reversed
I ordered four bearing hinges and drill holes for the hinges on top and bottom of frezer and fridge doors insert the bearing hinges on the holes and all the other part on the door were able to reversed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danny from PUEBLO, CO
- Parts Used:
- 241798231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Drive great stripped for ice eject. Heater bad
Loosened the 2 bolts 4 turns where it mounts inside the freezer. Lift maker off the bolts unplug 1 plug. Reverse to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teresa from SOUTHFIELD, MI
- Parts Used:
- 240350608
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
broken glass on top of crispers
Since the glass was broken and gone I just had to slide the new glass on top of the crispers. This was not really a repair, just an exchange of new for the old.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from KNOXVILLE, TN
- Parts Used:
- 241798231
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker would dump ice one time and then stop. Turning the ice maker off for a minute and back on would repeat the process.
I removed the two side mount screws with a screwdriver and disconnected the electrical plug to the ice maker to remove it. I reversed the process to install the new one.
It was the thermostat that was the problem, but I chose to replace the entire ice maker for only $25 more.
It was the thermostat that was the problem, but I chose to replace the entire ice maker for only $25 more.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from SAN FRANCISCO, CA
- Parts Used:
- 240350608
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Accidentally broke the glass insert.
Simply slide the new glass insert in!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leah from Tecumseh, OK
- Parts Used:
- 242252603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
After installing new ice maker water was not running into the ice maker.
Shut off water supply under the sink. Removed old valve and installed new valve. Turned water back on and within a couple hours the first batch of ice made.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- José from ORLANDO, FL
- Parts Used:
- 242044008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Fridge was cooling down enough the heating defrost was bad
I take 2 crew on front of the fridge take the cover and fan out replaced the part and put everything back it’s a easy job thanks guys for the parts from Orlando fl
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from WESTAMPTON, NJ
- Parts Used:
- 241798231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Ice maker stopped making ice.
The repair was fast and easy .I removed the ice tray , disconnected the wiring connector and lossend two screws. I removed ice maker assy.and repeated in reverse order to install. I also installed a new water filter. I had ice in about 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Lancaster, CA
- Parts Used:
- 240313703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
The original part was plastic/and broke
unscrewed to little bolts and installed the new/metal part we got rfom partselect.If we may say.this is a great company to buy from! Fast!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from GROTON, CT
- Parts Used:
- 241798231
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker stopped working. Part needed to repair it no longer available so had to replace the whole icemaker.
Loosened the two mounting screws (no need to remove them), lift off the icemaker and unplug it. Reverse the order and done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CAROLYN from SAN ANTONIO, TX
- Parts Used:
- 240350608
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Crisper glass shelf installed
Just like the video , just pull out the crisper drawers and slide the new one in. I also made sue that I had a quilt on the floor in case I dropped the glass shelf. Also if you are not sure of the model number you can try calling the store where you bought the appliance at which I had to do. I bought it at Conns and they just needed the phone number I used when I bought it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sam from Ravenswood, WV
- Parts Used:
- 241850615
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
Not making ice
Took out old replaced with new. Now it makes ice
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorothea from HICKORY, NC
- Parts Used:
- 5304498909
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Freezer shelf fell off door due to broken brackets
The part arrived on time. I unwrapped it and matched the brackets with the places on the door that fit. I gave it a tap and it was in place. I applied light pressure to make sure it wasn't going to fall out, then filled the bin as before. I was very pleased that the part I ordered was actually the correct piece and fit perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from GUNTERSVILLE, AL
- Parts Used:
- 242252603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
Water inlet valve stuck open
Turned off water to inlet valve. Unbolted valve from back of unit, disconnect water supply line from valve, disconnected water line to ice maker. Put on new compression ring around water supply line. Pressed ice maker line into new valve, installed valve back on unit, then connected main supply line to valve. Works like a charm.
Was this instruction helpful to you?
Thank you for voting!