25370089610 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from Lancaster, CA
- Parts Used:
- 240313703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
The original part was plastic/and broke
unscrewed to little bolts and installed the new/metal part we got rfom partselect.If we may say.this is a great company to buy from! Fast!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Benjamin from Jersey City, NJ
- Parts Used:
- 5304507147
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
The refrigerator door did not come for the opening swing to be reversed
I ordered four bearing hinges and drill holes for the hinges on top and bottom of frezer and fridge doors insert the bearing hinges on the holes and all the other part on the door were able to reversed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Andover, CT
- Parts Used:
- 5304507147
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Refrigerator door was not sealing correctly.
Remove screws from lower hinge and carefully remove the door. In my case it was the lower bearing, flip door upside down being careful to remove anything which might fall off first. I removed the door stop and then pulled the broken bearing out with pliers. Then I pushed the new one in and reassembled it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from RICHWOOD, TX
- Parts Used:
- 242252603
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
The fan had stopped spinning. According to the internet it should spin freely if I use my hand, but it wouldn't.
After pulling the fridge away from the wall and opening the paper backing on the bottom, I could see the motor. It's affixed to 3 metal ribs by 3 small screw/nuts. There is also a 12" wiring harness that led to a simple disconnect. Removing the disconnect and the 3 nuts was easy. However, there was no room to remove the motor with the fan attached. Between frame parts, the drip pan below, the ribs, and small, delicate copper tubing that can't get bent, it wouldn't fit thru any openings. So we rotated the motor inside the framework until the blade faced out, then reached in with a pair of needle nose pliers to remove the washer. Removing the washer is easy, it's just difficult to reach. With the washer off the fan was out of the way and very carefully (it was tight) the motor came out. Reverse was the same issue. Motor tight going in, not a lot of room to maneuver fan onto motor, and needed needle nose to tighten washer again. Make sure you tighten the washer before you install the motor on the prongs. Otherwise you need to remove it from the ribs, twist it to face you, then reinstall it on the prongs. Also, I felt I was stripping the nuts into the new motor. Turns out the holes in the motor aren't tapped. i realized the nuts are self tapping once I looked at them. I'm a big time DIYer and this wasn't bad at all. If your motor/fan assembly comes out whole, it's even easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from SAN MATEO, CA
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Repaired Oven Range Light Bulb
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Erin from NEW ORLEANS, LA
- Parts Used:
- 242193214
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old refrigerator door gasket was warped and door wouldn't stay tightly closed.
No tools needed. Popped out old gasket, cleaned/sanitizeddoor and popped new gasket into grooves. Door now closes tightly!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from GROTON, CT
- Parts Used:
- 241798231
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker stopped working. Part needed to repair it no longer available so had to replace the whole icemaker.
Loosened the two mounting screws (no need to remove them), lift off the icemaker and unplug it. Reverse the order and done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Montague, MI
- Parts Used:
- 242193211
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
moved into a new home and the inside freezer was iceing next to the freezer gasket.
purchased a new freezer gasket. It is still iceing in the freezer but now all over the top part and down the back. The new gasket does not secure tight enough around the entire freezer door when it is closed. It is secured properly to the door but does not "grab" tight enough when the freezer door is closed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from KNOXVILLE, TN
- Parts Used:
- 241798231
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker would dump ice one time and then stop. Turning the ice maker off for a minute and back on would repeat the process.
I removed the two side mount screws with a screwdriver and disconnected the electrical plug to the ice maker to remove it. I reversed the process to install the new one.
It was the thermostat that was the problem, but I chose to replace the entire ice maker for only $25 more.
It was the thermostat that was the problem, but I chose to replace the entire ice maker for only $25 more.
Was this instruction helpful to you?
Thank you for voting!
Fridge parts missing
I moved into a house with two guys that would have never even thought of fixing the problem. I'm a girl and couldn't live with a fridge without all it's parts so I looked in other places and decided to buy from here because of the reviews. I got the parts in two days with no problems at all, they were easy to install and the fridge looks better and we can make better use of the space.
I would recommend this store to anyone!!
I would recommend this store to anyone!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Sharpsburg, SC
- Parts Used:
- 240350609
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Glass
Order parts on sat.afternoon,and got part on Tues.aand installed in less them 2 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from CARIBOU, ME
- Parts Used:
- 240534701
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
retainer bar broke
took the old one off and snapped the new one in place. Very easy to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kimberly from BILLINGS, MT
- Parts Used:
- 240534901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Retainer bar cracked down center
With the excellent diagram provided by website, I was able to order the correct part. This part was not difficult to install, but so happy to know that this website provides instructions for more difficult projects.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sam from Ravenswood, WV
- Parts Used:
- 241850615
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
Not making ice
Took out old replaced with new. Now it makes ice
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from Orting, WA
- Parts Used:
- 240534901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the plastic shelf in the door of the fridge broke in half
i opened the fridge door and slid it into place
Was this instruction helpful to you?
Thank you for voting!