25370089612 Kenmore Refrigerator - Instructions

Pushed down on bar slots

Shut off water supply under the sink. Removed old valve and installed new valve. Turned water back on and within a couple hours the first batch of ice made.

The old gasket was dirty and old and it had ripped, so the fridge would no longer close. The new gasket came in and all we had to do was push it into the groves and make sure it was secure, and it was fixed. Saved me hundreds of dollars buying a new fridge.

I ordered four bearing hinges and drill holes for the hinges on top and bottom of frezer and fridge doors insert the bearing hinges on the holes and all the other part on the door were able to reversed.

After pulling the fridge away from the wall and opening the paper backing on the bottom, I could see the motor. It's affixed to 3 metal ribs by 3 small screw/nuts. There is also a 12" wiring harness that led to a simple disconnect. Removing the disconnect and the 3 nuts was easy. However, there was no room to remove the motor with the fan attached. Between frame parts, the drip pan below, the ribs, and small, delicate copper tubing that can't get bent, it wouldn't fit thru any openings. So we rotated the motor inside the framework until the blade faced out, then reached in with a pair of needle nose pliers to remove the washer. Removing the washer is easy, it's just difficult to reach. With the washer off the fan was out of the way and very carefully (it was tight) the motor came out. Reverse was the same issue. Motor tight going in, not a lot of room to maneuver fan onto motor, and needed needle nose to tighten washer again. Make sure you tighten the washer before you install the motor on the prongs. Otherwise you need to remove it from the ribs, twist it to face you, then reinstall it on the prongs. Also, I felt I was stripping the nuts into the new motor. Turns out the holes in the motor aren't tapped. i realized the nuts are self tapping once I looked at them. I'm a big time DIYer and this wasn't bad at all. If your motor/fan assembly comes out whole, it's even easier.

The center door hinge was still attached to the refridgerator so I only had to install the bottom and top hinges. I also moved the door handles to the other side so the doors open the "right" way. The hinges were just 2 bolts and 3 screws. Now, just if the repair man from our home warrentee company would show up to fix the refridgerator. It's blowing hot air!!!

The repair was fast and easy .I removed the ice tray , disconnected the wiring connector and lossend two screws. I removed ice maker assy.and repeated in reverse order to install. I also installed a new water filter. I had ice in about 20 minutes.

purchased a new freezer gasket. It is still iceing in the freezer but now all over the top part and down the back. The new gasket does not secure tight enough around the entire freezer door when it is closed. It is secured properly to the door but does not "grab" tight enough when the freezer door is closed.

I moved into a house with two guys that would have never even thought of fixing the problem. I'm a girl and couldn't live with a fridge without all it's parts so I looked in other places and decided to buy from here because of the reviews. I got the parts in two days with no problems at all, they were easy to install and the fridge looks better and we can make better use of the space.
I would recommend this store to anyone!!

Loosened the two mounting screws (no need to remove them), lift off the icemaker and unplug it. Reverse the order and done.

I removed the two side mount screws with a screwdriver and disconnected the electrical plug to the ice maker to remove it. I reversed the process to install the new one.

It was the thermostat that was the problem, but I chose to replace the entire ice maker for only $25 more.

took the old one off and snapped the new one in place. Very easy to do.

just pull the old off and put the new one on the magnetic strip inside the rubber was the key it just grabbed the area real easy.

Just pushed the grill on

Turned off water to inlet valve. Unbolted valve from back of unit, disconnect water supply line from valve, disconnected water line to ice maker. Put on new compression ring around water supply line. Pressed ice maker line into new valve, installed valve back on unit, then connected main supply line to valve. Works like a charm.