25370319213 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Albert from SAN ANTONIO, TX
- Parts Used:
- 243297613
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
There is no power, due to the COVID-19 pandemic there no Tech support available,
My repair plan is to continue buying parts for it until is starts working. I notices a large rusty stain on the back of the refrigerator, so I replaced the Ice Maker. Then, I replaced the Evaporator Motor. Yet nothing will come on.
I called Conn's Home Plus where I bought the Frigidaire Refigerator back in February 2014. The Tech said that It needs a Board-main Power (computer part). So I it ordered from PartSelect. It is due here by July 20, 2020. The Parts and Tech cost is now over Five Hundred ($500) dollars.
HELP!! I need INSTRUCTIONS, HELP!!!
Albert F. Alfaro in San Antonio, TX.
I called Conn's Home Plus where I bought the Frigidaire Refigerator back in February 2014. The Tech said that It needs a Board-main Power (computer part). So I it ordered from PartSelect. It is due here by July 20, 2020. The Parts and Tech cost is now over Five Hundred ($500) dollars.
HELP!! I need INSTRUCTIONS, HELP!!!
Albert F. Alfaro in San Antonio, TX.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chuck from GRIFTON, NC
- Parts Used:
- 242220204
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Water outlet tubing leaking in elbow behind water filter
Most difficult and time-consuming part of the job was clearing the refrigerator of food and shelving. Replaced tubing as it had split in the factory bend of the tubing directly behind the water filter. Take your time and don't get in a hurry.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Littleton, CO
- Parts Used:
- 241894223
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
freezer section upper shelf slide assy broken, captive ball slides fell out
Remove frozen food and ice cubes to coolers so they stay frozen.
Remove shallow wire shelf.
Slide out both sides of slide assemblies. Defective slide unclip the front corner front frame remembering to remove the plastic retention rivet first. It has a centre pin that needs to be pulled out first. Support the rest of the frame on the bottom shelf/basket frame
There is one cap head square driver screw to remove on the wall of the freezer holding the slide in place. Leave the other two flat head screws alone. Slide the defective frame off the other two flat head screws. Take new part and attachment is the reverse of the disassembly you have just done. The front frame corner clip is a bit difficult to put together there is a top and bottom spring clip then the plastic "rivet" where you need to push in the centre pin to retain it in the joint. [a bit flimsy so be careful].
The shallow basket should be carefully placed on the front and side clips, and make sure everything is square. Then slide the shelf to make sure it goes into the freezer properly. Then you can re-load the food and ice cubes.
Remove shallow wire shelf.
Slide out both sides of slide assemblies. Defective slide unclip the front corner front frame remembering to remove the plastic retention rivet first. It has a centre pin that needs to be pulled out first. Support the rest of the frame on the bottom shelf/basket frame
There is one cap head square driver screw to remove on the wall of the freezer holding the slide in place. Leave the other two flat head screws alone. Slide the defective frame off the other two flat head screws. Take new part and attachment is the reverse of the disassembly you have just done. The front frame corner clip is a bit difficult to put together there is a top and bottom spring clip then the plastic "rivet" where you need to push in the centre pin to retain it in the joint. [a bit flimsy so be careful].
The shallow basket should be carefully placed on the front and side clips, and make sure everything is square. Then slide the shelf to make sure it goes into the freezer properly. Then you can re-load the food and ice cubes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Lancaster, SC
- Parts Used:
- 241778315
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
GASKET WORN AND LEAKING
SIMPLY REMOVE THE OLD GASKET PULLING LIGHTLY BY HAND
THEN PUSHING THE NEW GASKET BY HAND
THEN PUSHING THE NEW GASKET BY HAND
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andres from Golden Valley, MN
- Parts Used:
- 241778315
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replaced door gaskets with new ones
Removed the old door gaskets by hand and attached the new ones by inserting the edges in the existing grooves
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from CIRCLEVILLE, OH
- Parts Used:
- 241778811
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Flipper mullion assembly broke
Removed 1 screw and unplugged flipper mullion assembly and removed it. Plugged in new flipper and one screw and done. Works as it should.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from POUGHKEEPSIE, NY
- Parts Used:
- 241894224
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Balls fell out so I needed a new slide
Basically took the broken piece off and put the new one on after removing the part on the new assembly I didn't need to replace ( It was still secure on the freezer) just popped that bad boy on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Culver from RHINELANDER, WI
- Parts Used:
- 241894224
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The little plastic bàlls came out of old part
Just took old one off and installed new. The company was great to work with.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from FREE SOIL, MI
- Parts Used:
- 243297613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Original ice maker not working leaking water water out door
Removed exterior housing, sliding old unit forward to release. New unit went in easily. Caution wires don't get pinched.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lorraine from Arlington, VA
- Parts Used:
- 242161202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
very Simple!
Insert the bottom part of the trim first, then pull up to snap on the top. PartSelect.com is a fantastic website!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JACK from OAK LAWN, IL
- Parts Used:
- 242046001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
unit was not cooling or freezing.
found the coil to be frozen like a block of ice. defrosted same, then looked up what defrost thermastat i needed and once it was received, i took the back of the freezer compartment off again, (two hex nuts, one on each end, and a small screwdriver to remove guard around fan. once this was removed, you then remove this panel, and you will see the evaperator coil, which will be frozen like a block of ice like i said. then remove defrost therm(small round piece with two wires connected to unit, disengage and re engage new thermostat. then put unit back!. no more freeze ups.also, therm was on top right of evaPERATOR. IT also snaps off on the bottom of thermastat. (just pull to or away from you and it should come off.
Was this instruction helpful to you?
Thank you for voting!