25370304410 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- ROBERT from CORP CHRISTI, TX
- Parts Used:
- 241798231
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
ICE MAKER NOT MAKING ICE.
LOOSENED THE TWO SMALL SCREWS THAT HOLD THE ICE MAKER UP INSIDE THE FREEZER. DISCONNECTED THE WIRING HARNESS. TOOK THE OLD ICE MAKER OUT AND JUST INSTALLED THE NEW ONE IN REVERSE ORDER. LATER THAT DAY I HAD FRESH ICE FOR THE FIRST TIME IN WEEKS!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Billy from CHATSWORTH, GA
- Parts Used:
- 241798231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
the gear was stripped on the old ice maker and had to be replaced
was very easy. just ordered a new ice maker which was delivered in a few days. The installation was so simple. Just plugged the new ice maker in and hung the unit on the 2 screws. And then tightened the screws with a 1/4 in nut driver.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Landover, MD
- Parts Used:
- 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bilb went out
replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Berit from Kirkland, WA
- Parts Used:
- 240358007
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old rusted freezer shelf
removed the old rusted shelf and replace with new one. Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Springfield, OR
- Parts Used:
- 240313703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Freezer door sagging due to warped hinge
Just block the door up so it doesn't fall off, remove the two screws, replace hinge, and replace screws. My wife could have done it. Metal replacement part is much better than the original plastic that warped from day one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bert from Saint Augustine, FL
- Parts Used:
- 240535101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Door Rack
Snapped new door rack into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melissa from Kansas City, MO
- Parts Used:
- 240535301
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Broken door rack
We simply replaced the door rack. It was extremely easy with the quick delivery of the product!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from Norman, OK
- Parts Used:
- 240364503
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The crisper pan cracked
I took the cracked pan out, waited for the new pan to arrive (2 days) and slid the new pan right in. It was so easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WILLIAM from EL PASO, TX
- Parts Used:
- 240535201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Door Rack
No tools were required to install
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Tiffin, OH
- Parts Used:
- 240535101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed a replacement for a broken doo rack
Snapped right in place, no problems at all.
Was this instruction helpful to you?
Thank you for voting!
the racks on my doors had snapped and I needed new ones
I just put them right on. Took about a minute to figure on the right way to put the racks on (push them down from the top, until they snap into place), and it was done in less than five minutes. I was worried that this wouldn't work - I couldn't find the exact item # to replace the racks that had been on there. But it turns out that they are pretty interchangeable - the sub racks that the website suggested worked perfectly for me.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James M from Charlotte, NC
- Parts Used:
- 240535001
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Replacing a freezer door rack
It was a perfect fit and snapped into place in seconds. No instructions were required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Boise, ID
- Parts Used:
- 242252603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set, Wrench set
Ice maker no working
Removed water line. Removed two screws holding valve. Disconnected line from valve going to Ice maker. Replaced screws and water line. Most important thing in working with Parts Select was the information they provided when I called them. I had called electrolux and was given no information and was told they would send out a repairman at which point I told them to get lost. Cost of part $30.00 vs service call of $75.00.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Gambier, OH
- Parts Used:
- 241559801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light socket burned out
snapped the wires from frig onto the proper prong and viola,it works. The proper prong is identified by the size because there are two prongs with the wires and two connecting prongs in the socket. I talked to a very helpful representative and she gave me the number for Frigidaire, when I was confused by the placement of the wire. Wish I had remembered her name to share with you. As it turned out I didn't need to call Frigidaire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jesse from Woodstock, GA
- Parts Used:
- 242252603
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Valve nut stripped
Old part threads : made in China (brass) New part : made in Mexico (steel). First, unplugged it from the wall. As for the valve, removed the two screws holding the valve in, disconnected the plug, took the pipe cutter, cut the blue line to the ice maker, cleaned up the cut, pushed that line into the new one and reassembled. Done!
Was this instruction helpful to you?
Thank you for voting!