25370304411 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- ROBERT from CORP CHRISTI, TX
- Parts Used:
- 241798231
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
ICE MAKER NOT MAKING ICE.
LOOSENED THE TWO SMALL SCREWS THAT HOLD THE ICE MAKER UP INSIDE THE FREEZER. DISCONNECTED THE WIRING HARNESS. TOOK THE OLD ICE MAKER OUT AND JUST INSTALLED THE NEW ONE IN REVERSE ORDER. LATER THAT DAY I HAD FRESH ICE FOR THE FIRST TIME IN WEEKS!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christina from Essington, PA
- Parts Used:
- 240535101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The original shelf cracked and fell off. No glue or tape would hold.
Just snapped the item into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Landover, MD
- Parts Used:
- 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bilb went out
replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Billy from CHATSWORTH, GA
- Parts Used:
- 241798231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
the gear was stripped on the old ice maker and had to be replaced
was very easy. just ordered a new ice maker which was delivered in a few days. The installation was so simple. Just plugged the new ice maker in and hung the unit on the 2 screws. And then tightened the screws with a 1/4 in nut driver.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- G V from Bowie, MD
- Parts Used:
- 242252603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
No ice - Replace water valve
TURN OFF WATER!! UNPLUG REFRIGERATOR!! Remove water fittings and electrical connector on old valve. Remove two mounting screws on pump bracket. Reverse procedure to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from vandergrift, PA
- Parts Used:
- 240524102
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
while cleaning the condenserI accidentally hit the fan blade and broke it
Had my 3 year old remove the 4 screws to holds the carboard in place. Pryde the old fan blade off with a screwdriver. slid the new fan blade on to the shaft then my 3 year old put the screws back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from Stow, OH
- Parts Used:
- 241796405
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Ice Maker not getting any water
1). Shut off water supply to fridge. 2). Move fridge out to gain access to back of fridge. 3). Remove poly line to water tube have a glass handy to catch any remaining water that might be in line. Some may have a foam insulating washer around water tube remove it first. 4). My Sears-Kenmore was a twist lock water tube have to turn it to left or right depending on brand to remove tube. 5). After removing make sure tube didn't just have water frozen in tube ( that was my problem ) run it under hot water frozen piece will come out. 5). Problem fixed, reverse directions to re-install tube!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Akron, OH
- Parts Used:
- 241798231
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Ice maker quit working.
The two screws that held the ice maker in place could not be seen do to there location. I could only get one hand inside do to space restriction.So I placed a mirror inside so I could see the screw heads and from point it was very easy to see and line up the nut driver on the screw heads. I then lifted it up and unplugged the wiring and installed the new ice maker. Works like a charm. Paul
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Al from Sarver, PA
- Parts Used:
- 240313703
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Original plastic hinge cracked across the middle
Removed 2 hex screws & old hinge, placed new hinge on cabinet & found that it didn't fit; one hole was about 1/8" off. Had to drill a new hole in cabinet top in order to attach new hinge. Hinge works fine now. I'm glad to find the hinge is metal; original one was plastic.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PAT from BATON ROUGE, LA
- Parts Used:
- 241796405
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Water Tube That Fills Ice Maker Leaking Water
Undone the water line that comes up the back of the refrigerator and pulled the water tube out the back of the refrigerator and reinstalled the new one and reinstalled the water line. Done
Was this instruction helpful to you?
Thank you for voting!
Refrigerator door sagged, had to push the door to close it.
Used wood blocks to raise the door off the lower hinge bracket then unscrewed the suspect hinge. Cut a small shim, two layers of soda can, to place under the lower edge of the new hinge bracket and doubled the washers by using the old one to ensure I had adequate clearance for the door. After a little silicone lube I installed the new hinge bracket. All better now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rusty from Howell, NJ
- Parts Used:
- 5303918774
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Fan would stop or turn slowly. outside of refridg hot
took off cardboard removed two screws holding fan housing. Removed new fan and housing from box and mounted new fan to new housing (two screws). Installed new fan and housing. reinstalled cardboard and plunged in power cord. Perfect fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Rockford, MI
- Parts Used:
- 5303918774
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Rattling Noise from behind frig
Initially, I traced the noise down to the evaporator motor area. I thought it was the fan blade so I ordered and changed it. Noise level better but still not good. Then I ivestigated problem area again. Removed the motor,discoverd that the motor shaft was loose /drifting which caused the "hummm" and uneven fan blade rotation. Orderd and installed new motor and all is good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Kiefer, OK
- Parts Used:
- 5303918774
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
broke fan blade while trying to remove dust.
Removed old fan motor and installed new one.Not much room for big hands back there.Flexible extensions valuable on this job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from Benton, AR
- Parts Used:
- 240535101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
top door rack was broken at the connectors
The new part fit perfectly! I just snapped it on! Thanks so much Partselect! You processed my order quickly, and I had it in my hands in a few days. What a relief to have this fixed! Thanks again.
Was this instruction helpful to you?
Thank you for voting!