25372112015 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Curtis from HOISINGTON, KS
- Parts Used:
- 241798231
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice Maker not producing / Clicking / Off-cycle
We love our ice here. I seem to replace the ice makers one to two times a year. Generally the ice cycle gets off for some reason and it starts making loud popping/clicking noises (gear grinding). Its easy to replace. Simply loosen two screws holding the unit to inside of freezer and disconnecting the wiring harness. Unit slide up and out. Replacement is super easy (5 mins or less). Bam! Ice!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from FREDONIA, KY
- Parts Used:
- 242193213
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
My gasket was worn out and torn.
The repair was much more simple to install than I would have imagined. I watched the video provided on your website. What a simple solution to a nagging problem. My fridge looks great again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cristina from MARLBOROUGH, MA
- Parts Used:
- 242193213
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Old gasket was torn and falling out
I removed the old gasket and cleaned the area. Then I started at the bottom and pressed the new gasket into the door. You must use firm pressure and go all around. It does get tricky hear the end as it seems like there is excess, but it will fit. Just keep using firm pressure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from PANAMA CITY, FL
- Parts Used:
- 241798231
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice maker broke again!
This refrigerator is less than 2 years old. I have had to replace the ice maker 2 times now. Cheap ass parts! Only one ice maker you can order so just be prepared to replace it yearly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carey from PORTSMOUTH, VA
- Parts Used:
- 241798231
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Didn't make ice
Unplug refrigerator , loosing two screws. Lift ice maker up to remove from position. Disconnect electrical connection. Reverse procedure to install new ice maker.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lloyd from HASKELL, NJ
- Parts Used:
- 241839405
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
bought brand new and kick plate was missing
just snap it on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from POTTSTOWN, PA
- Parts Used:
- 241798231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker stopped making ice
loosened 2 screws with 1/4 inch nut driver, disconnected electric connection lifted old ice maker out, replaced it with new one hooked up electric plug tightened 2 screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from CHICOPEE, MA
- Parts Used:
- 240495804
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
None fit perfectly
Just slid it down into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from SHERIDAN, IL
- Parts Used:
- 242252603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Water Inlet Valve not sutting off
very easy, 1 screw, 2 tube connectors, hardest part was pulling refer. out of enclosure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tommie from Port Lavaca, TX
- Parts Used:
- 241798231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
The ice maker quit producing ie
Purchased a new ice maker assembly and installed. Very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Benton R. from Elkton, VA
- Parts Used:
- 240495804
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Hook on end of snap-on freezer bin broke.
The existing bin fell off when the hook broke as the freezer door was opened. Finding and ordering the replacement part was about as simple as it can be. Delivery time was less than a week. Replacing the bin was just a matter of snapping it in place, which took all of 5 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Willard from Plymouth, MA
- Parts Used:
- 240385201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken draw
Pulled Out Broken Draw then put new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kasey from O'Fallon, MO
- Parts Used:
- 240338101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
had no shelf bin
Just snapped it on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karla from UNION, MO
- Parts Used:
- 241554901
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Socket set
Refrigerator light stopped working
The bulb wasn't the issue so I was hopeful the switch was. utube helped me some, but figuring my model was different than any on utube. Got the switch in and plugged it back in. Moment of truth. Didn't light. Ugggh! Out $50 for switch plus $20 for nut driver set.
Was this instruction helpful to you?
Thank you for voting!