25363212013 Kenmore Refrigerator - Instructions

Required a trip to the hardware store. Online research showed that Gorilla Glue would hold gasket in place and was recommended for that task. Needed to glue each side separately to keep the spline in the groove. Took far longer than it should have!

Disconnect the power. To install the Defrost timer which is located inside the console at the top of the fridge I followed a YouTube video. It is very easy. Keep in mind that the Defrost timer comes settled in defrost mode so the compressor will not start after the power is reconnected.There is a hole in the console just behind the Defrost timer where you engaged it with a flat driver and rotate the clock until the compresor start. Now the compressor works for 6 hours and stop for 20 minutes for the defrosting cicle. The freezer now is freezing the meat!!

Once the parts break and fall into the refrigerator you do not know how they were assembled.
Being a retired engineer helped me figure out how to replace the parts.
You will have to remove the shelf assembly and complete the work outside of the refrigerator.

There is no way to complete the repair with the wrong part, You have had my order since June 22nd, 2020 and the incorrect part arrived October 27th, 2020. You charged $7.79 plus $1.06 tax and $9.95 shipping. Please refund the entire amount including the shipping, since I did not ask you to ship the incorrect amount.

Came across your site and upon checking site out, I ordered the above parts. Repair was easy, thanks to your tutorial. Did not fix problem, so I posed a question to your site and it was recommended I replace the evap fan. I ordered that part. Thank goodness for next day shipping.
That repair was easy as well, thanks to feedback from one of your other customers who had a similar issue. That repair did fix the problem.

Ordered the part. When it arrived (extremely fast delivery), took the old part off and put the new part in. Perfect fit. Took less than one minute to exchange the old with the new.

Thanks a lot for such a wonderful, pleasant experience. Would heartily recommend your services to anyone in the market.

D. Hall

Just slid it in. Fit perfectly. Called the Help Line just to double check that the pan would fit and they assured me it would. Pan cost $20 less than through the Sears site because of lower price, lower shipping and no taxes. Oh, and the pan came in just two days. Very happy.

Easy to peel out old gasket, and new one tucked right in. I was embarrassed that it was so easy and I waited so long. Has made a big difference in how the frig looks and also operates.

Putting the shelf in was a no-brainer. It comes with matching slots and you can't put it in upside down or backwards. Only the right way!

Unscrewed screw from back of shelf pulled broken part out of slot it holds in and replaced with new one screwed the piece back in place.

just snap it on

I (female) fixed it by just inserting the brackets. Easy as pie. I was so happy that they fit.

Just lay the new glass shelf into the groves. The shelf was too big and would not fit properly down into the groves.

Unplugged refrigerator. Emptied freezer and removed ice maker and cover, need to unplug fan. Defrosted coils with hot water. Cut wires to thermostat as close to it ad possible to leave extra wire in case of an error. Stripped wire in new thermostat and put in shrink plastic then the wire crimp connector joining both light blue wires making sure wires were in before crimping them. Repeated with other dark blue wire. After used the heat gun to shrink the protective white tubing. The only thing i found not satisfying was tge tubing. It was too wide and too small. When i shrunk it did not cover the whole connector and was loose. I had to use a glue gun to cover both ends of each wire connector. Hope this helps other users.

Remove lower cardboard refrigerator panel. Carefully pull existing cracked fan blade off of the motor shaft and replace with new fan blade. Reinstall cardboard panel.

Removed glass shelf and frame. Unscrewed support from frame,replace with new support and screwed it into the frame, attach drawer and replace shelf in fridge .