25361112102 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Arsen from Glendale, CA
- Parts Used:
- 5303918202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
i smell very bad smell coming from refrigerator
I started look inside ,disconnected power, and open all possible compartments to see any burned part. Fortunately I fined a small part look like melted and then i went online and make my research .Then i ordered that part and change it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marcos from E STROUDSBURG, PA
- Parts Used:
- 240362601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
The Refrigerator was not cooling properly. At 40-45 degrees milk spoiled
My upper and bottom air diffuser was missing.
Purchased both air diffuser and placed it.
Purchased both air diffuser and placed it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andy from GOOSE CREEK, SC
- Parts Used:
- 218909912
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Freeze would not re-start after temp rose above 23 degrees.
Unplugged the freezer. Located the Run Capacitor (next to the compressor). Removed the wire holding bracket, removed the Run Capacitor from the Start Relay. Installed the NEW Capacitor, re-installed the holding bracket. Plugged the unit in, looking at the display for the proper start-up sequence data. All is good - freezer operating for another 10+ yrs. NOTE: When removing the Run Capacitor, beware the COMPRESSOR could be HOT to the touch.
Was this instruction helpful to you?
Thank you for voting!
Rail broke at the most support place
Took out top shelf, remove old screw and rail . Replace with new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from Newberry, SC
- Parts Used:
- 5303918202
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
the freezer frosted up and the fridge was not getting cold.
I watched the instructional video and did what it said.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from N RICHLND HLS, TX
- Parts Used:
- 5303918549, 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Refrigerator too warm
The parts were easily replaceable. No special instructions needed. Just identify and remove and replace. I didn't know which specific part needed to be replaced (both reported to fix my problem) but neither part was very expensive so I replaced both. No special tools needed. 1/4" nutdriver and phillips head screwdriver. Repair took about 30 minutes. I did have to make an adjustment on the defrost timer (a small dial on the unit) I just set it how the old part was set. I immediately knew it was going to work when I plugged the refrigerator back in and the fan motor inside the freezer kicked on. Easy peesy...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from PARRISH, AL
- Parts Used:
- 240530701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
BROKEN RIGHT DRAWER RAIL
REMOVED STUFF FROM SHELVE AND THEN REMOVED SHELVE AND TURN UPSIDE DOWN REMOVED SCREWW AND REPLACED RAIL AND DRAWERIN TRACKS REINSTALLED SCEW AND RETURNEED TO REFRIGERATOR
Was this instruction helpful to you?
Thank you for voting!
Refigerator not cooling
I followed your video instructions, is very important to have this information.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from VAN WERT, OH
- Parts Used:
- 5303918202, 215846602
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Refrigerator not working, freezer working
I initially replaced the defrost timer, and later replaced it and the defrost thermostat. The defrost thermostat was the faulty component
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from STERLING, VA
- Parts Used:
- 5303918774
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
Condenser motor burned out
I followed the instructions on your website, made it a simple as possible. Very tight work area sometimes fingers only, but a little patience works.
Saved at least $300. By not paying a repair person.
Saved at least $300. By not paying a repair person.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from N HOLLYWOOD, CA
- Parts Used:
- 5303918774
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Fan was off kilter and began rubbing the frame which is caused it to slow down and make an disturbing audible noise.
Before buying the part, I watched your video and realized it was extremely simple to remove and replace. Item was to take 7-10 days and I received it in 4. Took longer than 15 minutes because I had to move the fridge forward, get my tools and a vacuum, get a cup of coffee and get to it. Very easy and the video was exactly step by step. It took longer to vacuum all of the dust bunnies than to replace the part.
Honestly, I was in the market to buy a new refrigerator but now I believe I'll wait several more years. Thank you for your support.
Honestly, I was in the market to buy a new refrigerator but now I believe I'll wait several more years. Thank you for your support.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CECIL from PHOENIXVILLE, PA
- Parts Used:
- 242193205
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
Gasket was oversize and compression spline would not stay in door groove
Required a trip to the hardware store. Online research showed that Gorilla Glue would hold gasket in place and was recommended for that task. Needed to glue each side separately to keep the spline in the groove. Took far longer than it should have!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from ORMOND BEACH, FL
- Parts Used:
- 240505801
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light Switch not working properly
After unplugging the fridge, I took a small flat headed screwdriver and carefully pried off the light switch from the inside, right side of the refrigerator. I disconnected the 2 wires from the switch and replaced it with the new switch and pushed it back into the frame of the fridge. Done !! Very very easy !! Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- w l from PIKESVILLE, MD
- Parts Used:
- 242193213
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
crack
pull off the old gasket and push on the new one into the channel...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- janet from Parryville, PA
- Parts Used:
- 242193213
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
torn and cracked gasket
Took off the old one, replace the new one in less than 5 minutes
Was this instruction helpful to you?
Thank you for voting!