1069545782 Kenmore Refrigerator - Instructions

removed screws that held the ice maker in place, then removed the cover (popped off) The drive element was easy to remove, three screws and it was out. I put in the new part and reinstalled the icemaker with the three screws that hold it in place. I never call Sears for any repair. They use contract help and I have heard horror stories about those guys!

watched video. Very easy

simply removed wires from the old motor and gently lifted it out by by the metal clips - put the old bracket on the new motor, snapped on the new fan, replaced the wires, reinstalled the shield. All done in about 15 min.

ridiculous how a tiny plastic broken part required a full motor assembly replacement. that being said, i went online, found this website and easily identified the part i needed to order. i was impressed when it arrived within a couple of days. removing the old motor and replacing the new was a piece of cake...and i am NOT mechanically inclined,

Same as everybody else on this post. Real easy. Actually, I just wish I would have done it sooner.

We rolled the refrigerator out away from the wall and it was obvious where the break was located. We took out the old water spout for the ice maker and replaced the tube and the tubing from the solenoid. We turned it on and soon we had water dripping everywhere. We unloaded and defrosted the freezer which got all of the remaining ice that was stuck in there. We put everything back together. I read in some instructions in the manual that it might take 24 hours for the ice maker to reprogram itself and start producing ice. I was only about 12 hours and we had ice again and everything worked well. You really do not have to disconnect the water from the main line, the solinoid controls that part of operation and turns the water off until the ice trays are free and clear.

JLB

I called the local Amana repair man, wanted $150 for a new ice maker because they could not get the part I needed. Found Partsselect.com and the part cost $17 with shipping. They saved me over $100. The repair was very easy too, just removed a couple of screws.

Thanks,
Matt

Cut off old nozzle. Tried electricians tape to join the old and new tubing for fishing, but tube with tape on it, wouldn't fit through hole in hinge at bottom of door. Fished nylon twine through new tube then old tube from dispenser end and was able to feed old tube out and new tube in. Fast and easy. Took more time to clean all the dust and dirt I found down under, than to make the repair.

The part received was a straight replacement part - no modification required, just a simple remove and replace. This made the job really easy. Used the socket set to lower the front wheels to move the refrigerator, the nutdriver to remove the back cover and the valve, and the adjustable wrench to remove the water line. I had to cut the supply line tubing because the ferrule was too far up the line to make a good seal (minor leak quickly corrected with parts available in the kit - nice touch!) What took the most time was cleaning the coils and lint, etc. - hey I hadn't moved the unit in years! - but I did not include the 45-60 minutes this took in the repair time. Directions supplied were clear and easy to follow - but in my case I could have done the job without them - easy to see what needed to be done, but the stated precautions were nice.

remove shelves in freezer compartment incl.holders(slide up to remove)
Remove lamp/shield
Remove panel (six phillips screws)
disconnect motor
pull off fan blade
squeeze bracket holding motor to remove
remove motor.
Re-assemble (in reverse)

This is in a rental house; Refrigerator/freezer has been off for a few weeks so just opened the freezer door and used screwdriver to pry out one corner then pliers to grab and pull old gasket (seal) off. Had the new one laid out overnight to relax it; placed one corner on and then the opposite corner then repeated the other two corners. Positioned the keeper edge plastic all of the way around to place the gasket in the door. Closed the door to check the seal and plugged unit back in. Waited and then checked air temp with hand held IR temp gauge. All checked good, no cold spots anywhere. Piece of cake!

Very easy. Your online video was agreat help.

The replacement valve was identical to the old one, so I didn't have to use any of the adapter parts sent with the new valve. This made the installation rather simple. After removing the back cover on the lower part of the refrigerator, I turned off the water and electrical supplies, and removed the water supply line to the valve. Then I removed the two screws securing the valve to the refrigerator. Next, I removed the two electrical connections from the valve, and unscrewed the plastic nuts holding the tubing to the valve. I didn't have to use a wrench to do this as they were hand tight, so when I attached the tubing to the new valve I tightened the nuts hand tight. This seemed to be sufficient and avoided the possibility of stripping the nuts. After checking for leaks, I attached the electrical connections and secured the new valve to the refrigerator. Then I attached the water supply line, but before replacing the back cover, I turned on the refrigerator, and let it cycle through it's first load of ice.

The hardest part of this job was removing the front cover over the water and ice dispensing unit.

Step 1: remove front cover by inserting flat head screwdriver into one of small slots on the bottom side of the cover. Push up firmly, but not too hard (don't beak the plastic cover). As you are pushing up, slightly pry the bottom edge away from refrigerator door. Then, do the same for the other side.
Step 2: Now with both edges slghtly pried away for door, you will now need to use your hands and apply an upward pressure on the cover. (Understand that there are three tabs on the top side of the cover that must come about 1/4" out of slots on the top side of the door.) Try wiggling the cover, while applying upward pressure. You may find the door handle restricting one of the tabs, but you can slide the cover to the side to get it out.
Step 3: with the cover removed, now you can use the nut driver to remove the one (1) screw that holds the mechanism in place. Be sure to see how it fits over the dispensing lever.

Step 4: Install the new delay mechanism by inserting the prong over the dispensing lever and seat into place. Insert screw and tighten.
Step 5: ensure that you installed the device properly by actuating the ice dispenser. If everything is OK, proceed to next step. If not, make sure you installed it correctly.
Step 6: Reinstall front cover by insering the three upper tabs into slots at the top of the dispensing area. Apply downward pressure with your hands, then push the bottom side of the cover in. You should hear them snap into place.
Step 7: Dispense ice into a glass, add water, and enjoy your finsihed project

First of all it's nice to have an exploded view of the ice/water dispenser.
First remove the trim around the ice'water dispenser by carfully prying the bottom out and popping the trim up to release the top.
Remove the 2 screws that hold the light switch and light, move out and to the right, do not disconnect.
Remove the 2 hex screws that hold the old arm in place. This will allow the arm to drop down so you can remove the arms' ice guide.
The arm has a spring for tension on the right side. Remove it and retain.
Above the water dispenser is a screw that holds the ice door closer spring, remove this screw and slide out the spring loaded closer
Loosen the right screw that holds the water dispenser, it is spring loaded.
You should now have room to remove the old ice dispenser arm.
Slide the new arm up into place behind the ice dispenser door
install the spring tensioner to the right side mount screw at the same time align it with the left side of the water dispenser arm. The ice dispenser arm and the water dispenser arm share this mount so both arms have to be in place in order for the arms to work properly.
Install the left mount and screw of the ice dispenser arm
Install the ice dispenser arm's ice guide using the screw removed earlier.
Next reinstall the Ice door tensioner spring and screw making sure the metal arm of the ice door is engaged in the slot of the tensioner.
Finally reinstall the screws to the light swithch and light bar and snap the trim back into place.