2539639083 Kenmore Refrigerator - Instructions

The repair was straightfoward. The evaporator motor I received from partselect was a different model with different wiring configurations. I cut the wires from the new motor per the instructions I received with the new motor and I did the same with the wires that connect to the fridge. Once I matched the wires and secured them with electrical caps I began to put the evaporator motor to the base and started screwing the screws the way I took them off. Once I connected the wire harness to the back of the freezer and turned it on I noticed a big difference in air flow. I was surprised at how easy it was to fix my refrigirator problem. It's been a few weeks now and the fridge is cold and working like it should. Don't be afraid of this task. it's very easy and will save you a ton of money. Thanks partselect.

first I replaced the timer control hoping thats the problem,unfortunately situation the same ice build up on the freezer.so I replaced the defrost thermostat.right now I'll still observing the condition if still the same.may be in couple days.so far its good.and to replace the parts is not difficult and easy.

Removed screws that fastened bracket to fridge. Next, I replaced the motor and carefully lined the brackets up so the motor would rotate smoothly. Put the fan blade on the motor and screwed the brackets back on the fridge. Motor kept popping out of alignment while I was screwing the brackets back in but I kept snapping it back in till it stayed.

Unplugged refrigerator. Removed control knob and cover. Unwired control and removed same. Removed plastic tube from old capillary tube and placed on new unit. Installed and wired in new unit, making sure new unit was in the "off" position. Plugged in refrigerator, turned control knob to the first numerical setting, and was rewarded with the startup of the refrigerator compressor. Voila!

bottom left cornerof fridge defrost timer replaced two bolts and a wire

Ordered the new part-Unplugged the refrigerator - took off the cover over the defective timer - put in the new part put the cover back on - plugged the refrigerator back in - so far, so good!~

I watched the videos (they really help) and followed the steps. Everything went smooth with no surprises

removed everything from door, removed screws in gasket around door, laid door face down(insulation side up)applied rtv around edge of gasket and door, waited 10 minutes and started with top screw in middle of top then middle of sides and bottom then installed remaining screws checked levelness of refrigerator, the you are done

I order defrost timer then replaced it but it seemed doesn't work. I order defrost thermostat again then it worked fine until now. Thanks. Part selects.

Unplug the refrigerator. Removed the right hand top shelf. Used a 1/4" nutdriver to remove rear center mounting screw for Control Housing. Used Phillips screwdriver to remove two mounting screws for timer. Unplug cable from timer and plug it into the new timer. Install the new timer and re-install the Control Housing. Plug in the refrigerator and adjust the timer to start the unit. This was a snap with the diagnostic provided by Part Select. At first I thought it was the fan rubbing but when I removed the cover (two screws) it was obvious that wasn't the problem. The diagnostic hinted that it was either the timer or the motor capacitor making the noise. Because the noise continued after turning OFF the control, I thought it was the timer...I was right.

I should have ordered start kit instead of start capacitor. The start cap astir did not fix problem so I ordered kit. Compasator comes as part of kit. Followed enclosed instructions. Cut existing wires and reconnected new wiring. Simple as that. It's a plug in item. Now worried it may be working to good. Freezer down to 10 deg. Watching to see if compressor is running to long. Seems ok lol. Wife hates me now. She wanted new frige.

Unplug the refrigerator unit from wall. I removed freezer rack, plastic light cover, the ice rack shelf on the right side, then removed the plastic back cover panel, (4) retaining screws, gently tilting the panel toward me, unplug the wiring harness by depressing the clips on the side of the plug, removed panel from unit, set aside. If the unit was froze up, so I defrosted the cooling coils carefully with a common hair dryer until it was thawed. Be careful not to touch or bend the coils , since they are very fragile and SHARP! I located the old thermostat unit attached to a straight length of coolant line. The new unit looked like the old one, so it was easy to locate. I cut the two wires of the old unit close to the round base to make sure I would have enough wire to reconnect. Since my new unit did not indicate a polarity(Neg or Pos), I just wired each wire I cut to one of the new unit. I used the shrink tubing provided and heated the shrink till it was fully melted. I double ck'd to see if the wires were basically waterproof and a good connect. Also, before I replaced the rear panel, I made sure that both wires I had spliced had a drip loop to it so water would not drip down into the newly spliced union. Also made sure the wires will not interfere with the colling fan on the back of the rear panel. Reverse the procedure in reassembling. Plug in unit, and wait and listen for the unit coming back on..I kept a regular thermometer in the upper and lower compartments. Allow 24 hrs. for the unit to return to normal operation. It may defrost several times till the whole operation is back in sync.

I needed to determine if the heating coil was ok. I bypassed the thermostat, rotated the defrost timer manually with a flat screwdriver until it clicked. The coil heated up and turned a glowing red. So the coil was ok. After looking at the wiring diagram located on the back, the only parts in line was the timer and the thermostat. So I ordered both, replaced them, and everything is working fine. I went online about noon on Thursday, placed the order. The shipping indicated 2-3 business days. To my surprise, they were delivered to my home on Friday, mid morning. Great service from Part Select.

dismantled the top rear panel of the freezer and found I had the wrong part. Hand started the fan motor and it has been working fine since.

we removed the food from the freezer, disconnected the fridge , removed the cover, the evaporater fan was running, condeser fan was running, then we checked heater with multimeter and it was ok. next step we replaced the frostimer, and defrost thermostat . and then the refrigarater was working ok, problm was the frost thermastat damaged.