2539305362 Kenmore Refrigerator - Instructions

Based on the website I decided it was most probably the defrost timer, and that was correct. I ordered it, watched the video, and two days later the part was at my door. Took the nut driver, removed 4 screws, then removed the old defrost timer, installed the new one, re-installed the whole plastic assembly with the four screws, and done!!! Couldn't have been easier.

From most posts I've read, the defrost timer was the culprit so I blindly ordered one. Easy install but did not fix the problem so I broke out the ohm meter. The only other 2 items it could be all tested good with my meter so I bypassed the defrost thermostat (per forum help...actually quite easy)and it defrosted fine, which told me I needed a new defrost thermostat. Installed fairly easy and problem gone.

unplug power from ref removed old light socket only difference wired a little different checked new socket compaired to old checked terminal ends small big looked at wires big,little plugged up put in new light blub plugged ref power back on work power off pushed socket bac in power on works

Removed the vent cover at the bottom. Removed the screws. disconected the harnes and put the new timer in. This was a very easy fix. Thank You!

Took old defrost pan off, put new one on. Had to bend new defrost pan a little for it to fit..

We ordered end pieces for the shelf holder, attached them to the long piece and snaped them into the door. Three minutes to open the box, attach, and close the door. A less than 20 dollar repair and success!

Found the part on this site ordered and received part in 3 days. Took approx. 10 min to replace. Thanks for the quick service.

Dear Part-select,
I had a fridge that was not working food was melting in the freezer, Beer was warm. You get the picture anyway using your site I found the parts needed to to fix the issue in fact I ordered two parts one fixed the issue 50% and the other like 30% of the time! both parts with overnight shipping were cheaper than 1 part if purchased at our local appliance part outlet:) not to mention the cost of a repair person. Thanks again! . Keep up the good work


Tom Houck
Spokane, WA
Houck Photo
509-723-3418
tomhouck1@comcast.net

Needed to saw the pieces. PUrchased hacksaw.
Son sawed the pieces. Went in like a piece of cake.

I replaced the shelf end caps in the shelves of my fridge and I also replaced the gasket around the door.

Every time I would open the door, things would fall out because the shelves were giving, because the end caps were broken. Once I got the new ones, I was amazed that these parts are still available and that they lock right in with no problem. Once you get one in, you then have to place one end of that retaining bar into that, very tightly, making sure the end is completely secure in the cap. Then you can lock the other cap to the other end, lock it into place in the door and whala! It is just that simple.


Now the gaket is another story, it is best to soak the gasket in hot water first to draw it up abit so it will be snug and also to use lubricant such as petroleum around the inside where it is going to fit to the door. This made it extremely easy to afix to my door with no problems. I am so glad for this site.. hundreds of dollars saved!!

Pulled the few end caps off the retainer bars, pushed the new ones in, and used a medium hand strike to seat the end caps in the doors slots.

Followed the instructions provided in your video, took less than 15 minutes and works like new. Thank you for the parts and the advice.

1. Turned off the cooling cycle and unplugged the refrigerator.
2. Removed all of the shelving and bottom basket.
3. Removed rear covering in the freezer section.
4. If frosted over, manually defrost coils with hairdryer.
5. Located original thermostat and after marking the wire locations cut the wires and removed the Thermostat.
6. Connected matching wires using a lighter to melt the wires together. Wrapped repaired wires with electricians tape.
7. Unable to install the thermostat in the recommended location (freezer is a tight fit) the new part was installed at the original location.
8. Replaced the rear cover and shelves.
9. Plugged in the refrigerator and set the cycle back to cooling.
10. Monitored freezer coils couple of days/weeks depending on how fast they freeze over (slots at bottom of cover) to validate if problem solved.

Having tried PartSelect.com before, I was very comfortable with the process. Input my symptoms and the feed back I received was that one of the 2 things (Defrost Timer or Defrost Thermostat)might need replacement. Since the cost was not much and over night shipping would cost more than the product, I decided to order both the parts. Changing parts was a breeze. The instructions posted by others on your web site were very easy to follow. You guys save me a bundle every time I have any thing going worng with any of my appliances.

Removed shelf brackets to allow the removal of the evaporator sheetmetal cover. Unpluged wires to thermostat ,removed defrost timer and plugged in new timer,(front left lower kick panel). Cut and resoldered wires to new thermostat reinstalled thermostat and cover in reverse order. I knew what parts I needed and how to repair the unit,however your customer comments were spot on and would help anyone perform a successful repair (you provide a helpful service for the public)