25363093302 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Aaron from ODESSA, TX
- Parts Used:
- 5303918549, 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Fridge was't cool
I just followed the instructions on the videos.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Reginald from WEST PALM BCH, FL
- Parts Used:
- 5303918549
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Noise from fan
I watch the video on your site and this make iit very easy to do. That repair that tooks me 40 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from NEWHALL, CA
- Parts Used:
- 5303918549
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Evap fan motor comes on and off will not stay running
pulled back panel to get at evap fan motor cut wires to remove reinstalled hooked up wires
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kasey from O'Fallon, MO
- Parts Used:
- 240338101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
had no shelf bin
Just snapped it on.
Was this instruction helpful to you?
Thank you for voting!
Drawer rails wore out for the meat drawer
Took off worn out rails and replaced with new ones using a Phillips screwdriver.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from PHILADELPHIA, PA
- Parts Used:
- 5303918202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Evaporator was freezing up and was running non stop
I tested the components in the refrigerator defrost function. I used digital multimeter and checked for continuity. Defrost thermostat must 32 degrees or lower.
Was this instruction helpful to you?
Thank you for voting!
refer door hinges were lost during the move in to our first home.
The center door hinge was still attached to the refridgerator so I only had to install the bottom and top hinges. I also moved the door handles to the other side so the doors open the "right" way. The hinges were just 2 bolts and 3 screws. Now, just if the repair man from our home warrentee company would show up to fix the refridgerator. It's blowing hot air!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from SOUTH HAVEN, MN
- Parts Used:
- 5303918549
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Fan motor in the freezer was not working. The freezer was still cool enough to keep the food froozen, but the refrigerator was not keeping the food cool and the liquids were getting warmer than normal.
Very easy process. Watch the YouTube video, it goes step by step for the repair. The part was $33, shipping was $6. Take your time and fix it yourself or pay $500 for a new refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Adam from BERKSHIRE, NY
- Parts Used:
- 5303918549
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Freezer worked, no fridge
Removed panel over the motor in the freezer department. Removed screws holding the motor in, unplug wires. Reversed process to install motor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JACOB from YOUNGSTOWN, OH
- Parts Used:
- 241537103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Refrigerator did not cycle
Installation was fairly straight forward. The major complaint is that the problem returned 2 weeks later. I don’t know if I care to re-invest in another switch.
Now what?
Now what?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DANIEL from CAPE CORAL, FL
- Parts Used:
- 5303918202, 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
FREEZER COMPARTMENT NOT COLD ENOUGH (20 DEGREES)
REPLACED TIMER-DEFROST 215846602..REPLACED THERMOSTAT-DEFROST KIT 5303918202..REPLACED CONTROL, TEMPERATURE 5304421256..RECHARGED SYSTEM WITH 134A...ALL FANS WORKING...COMPRESSOR RUNS.. FREEZER STILL NOT GETTING COLD ENOUGH...HOLDING AT 20 DEGREES...ANY SUGGESTIONS..THANKS..DAN
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from MONTGOMERY, IL
- Parts Used:
- 5303918202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Coils frozen over. Refrigerator not cooling
I cut wires from bad thermostat and removed it . Stripped wires and crimped connectors on new thermostat and wires from old thermostat. Used heat gun to seal sleeves over connectors. Very helpful video from this site Thanks, you will be my go to parts supplier from now on!!!!!!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Salvador from SANTA ANA, CA
- Parts Used:
- 5303918202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Freezer worked, refrigerator didn't. Ice build up on coils.
Unplugged refrigerator. Emptied freezer and removed ice maker and cover, need to unplug fan. Defrosted coils with hot water. Cut wires to thermostat as close to it ad possible to leave extra wire in case of an error. Stripped wire in new thermostat and put in shrink plastic then the wire crimp connector joining both light blue wires making sure wires were in before crimping them. Repeated with other dark blue wire. After used the heat gun to shrink the protective white tubing. The only thing i found not satisfying was tge tubing. It was too wide and too small. When i shrunk it did not cover the whole connector and was loose. I had to use a glue gun to cover both ends of each wire connector. Hope this helps other users.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Betty from POMONA, CA
- Parts Used:
- 240356501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broken right side rail on meat drawer
Removed two top trays, fixed the rail on the second tray by removing one screw and sliding out broken piece, and sliding in new arm and rescrewing. Screw was a little tight, but went in.Very impressed i was able to do it myself with your simple instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from ROANOKE, VA
- Parts Used:
- 240356501
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
rail was broken
After removing meat tray the entire shelf including rails needs to come out. Once out a single set screw in the middle of rail needs to be removed. You can then slide the old rail across and then pull it out. Then insert new rail, slide across to lock in place. reinsert set screw. Don't over tighten. Be careful when replacing shelf as left side has air opening for drawer that must to match up.
Was this instruction helpful to you?
Thank you for voting!