36368965897 Kenmore Refrigerator - Instructions

Opened back,found fan not moving. Cleaned out dust and dirt. Received exact fan motor. Easiest fix I ever performed(very unusual). Fridge now runs great! Also, water line to in-door ice and water dry roughted and sprung leak. Replaced tubing.

Vacuumed the area around the compressor, removed the PTC relay switch cover, pried the broken relay switch off the unit with a screw driver and replaced with the new relay switch. Replaced the backing of the refrigerator and tested, within minutes the work was confirmed.

First I turned off the water supply. Then I removed the ice bin and the ice maker by removing 4 screws and 3 electrical connections. This allowed access to the evaporator fan which was not moving. To remove the evap fan I removed two screws that hold the fan bracket. The fan assembly now had to be pushed back and rotated to remove from hole. There are 3 electrical connections that have to be disconnected from the fan, one ground wire that also is connected to the fan bracket and 2 power connections. Installing the new fan was the reverse of the above except the power connections were in a different location and i had to use the extension wires provided with the new fan to have the length needed to make the connection.

Very easy. Removed all the parts from the fridge. Removed the glass. Unscrewed the two screws holding the rails to the front and rear support. The front support that has the "fruit" and veggie" settings, you have to remove the plastic name cover off to expose the front screws. The install is the reverse of the removal. The only "tricky" part is remembering the configuration (left from right) and removing the vinyl edging that the glass rests on from the old left and right rails and placing it on the new rails. Good Luck to all! "Quality is not an act, it is a habit" - Aristotle

Unplugged frige, removed top shelf, pulled broken fan blade off. Replaced with fan blade just purchased from PartSelect. Very simple repair. Orderd and recieved the right part.

I placed the new part on the end of the freezer door guard and firmly pushed it in until it 'clicked'. Easy as pie! The more difficult part was to remove the broken off part inside the opening of the freezer door hwere the new bar end was to be inserted. I finally used thin nose pliers to reach in and grab the broken off part.

Found the part I needed in only a few minutes on the website and ordered it in less than 5 minutes. The part came within 2 days and I simply removed 2 screwes from the old part and installed the new part and replaced the 2 screws , the easiest repair job that I have ever done in my home. Thanks

I took out the vegetable bins and slid in the part. Replaced vegetable bins. Works perfect. I was told locally that GE doesn't make the part any more and that I wouldn't be able to find one. First place I looked on the net was you and found it with no trouble at all. really thrilled to get it. Thanks

I used pliers to pull lightly on the head of the switch, while I inserted a small flat head screw driver into the base of switch and gently worked around the edges to free it from the panel.

After replacing the light bulb and still no light I manually pushed the light switch button. Intermittently the light would come on then go out. I removed the power plug from the power source then replaced the light switch. I plugged the refrigerator back in and now I open the door the light comes on and stays on until the door is closed.

The old switch was hard to remove. Thinking that I may have to loosen the wires I used a socket wrench to remove a clamp. This was unnecessary. In the end the switch did come out using a large size screwdriver. The problem was that the expanding plastic tongue is not visible from the ouside so you have to try to feel your way around. If i had ordered the replacement before and not afterwards I would have seen this before hand.

I first unscrewed the broken right rail from the back piece and replaced with the new rail. Did the same for the left piece side. Attaching to the front rail was challenging because I took a while to figure out how to remove the cover (where the pictures of the vegetables/fruits are). But if you just get a narrow flat-head screwdriver under there, it just pries off. Then you can get to the little screw that attaches the side rails to the front piece.

I ordered two switches, replaced both with a knife in 10 minutes. Interior light works, thanks.

replaced condenser fan motor.
also, i ordered the part on a tuesday and received it the next day. partselect is a very well run company.

replaced lights in refrigirator and freezer